$9.33Was $17.28
A low-poly vase built from big flat facets that twist as they rise, so light catches every plane differently. 5.5" across its widest and 3.9" tall, printed in one piece.
Design by Harry
$1.34Was $1.99
An articulated dragonfly: the body and each wing are cut into flat segments joined by print-in-place hinges, so it flexes in the hand and settles back flat when you set it down. It prints as one piece with no supports, 4" across by 2.7".
Design by Tybob24
$3.40Was $5.04
A cube of eight hinged blocks that folds in on itself: twist it one way and it turns inside out, fold it the other and it closes back into a cube, which is the whole trick and the reason one stays on a desk. It prints as a single piece with its hinges already in place, in two sizes, and needs no supports or assembly.
Design by Print3DFamily
$1.62Was $2.40
A crocodile printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles and curls in your hand. 4.0" long, printed in one piece.
Design by ThePrintDrawer
$7.09Was $10.50
A slug that ripples: the body is a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. About 3.0" curled, printed in one piece with no supports. Enlarged and remixed by yusuffles from matveymoo's "Curled up Friendly Slug", and sold under the same share-alike licence.
Design by yusuffles
$1.65Was $2.44
A lucky toad, printed in one piece with no supports, about 1.9" across and 2" tall with its little belly. Four come at the bulk rate.
Design by Ake Studio
$1.34Was $1.99
A plump bee that clips onto the top of a straw, wings raised and its stripes cut deep enough to read across a table. It suits the 10 mm Stanley straws, is 1.6" by 1.5", and prints in one piece with no supports.
Design by Morganja
$2.02Was $2.98
A monster printed as a chain of flexing segments - horns, a ridge of spines down its back and a tail that curls - so it stands up, slumps and wriggles. 3.9" tall, printed in one piece with no supports, in one colour or three.
Design by TinkerLink
$1.34Was $2.09
One small fox, about 1.7" tall and 1.9" long, head up with its thick tail curled along its side. The designer's plate carries twenty-five copies of this fox, and the listing is for ONE of them - add as many as you want. The plate prints in one go with no supports and no AMS, which is what it was built for.
Design by AkeStudio
$8.99Was $13.32
A bowl for rinsing rice: the water swirls through the grain and pours off the side while the rice stays put, so you stop losing half of it down the sink. Two sizes - 6.9" across and a smaller 4.8" - each printed in one piece, with the drain holes and the pouring lip part of the bowl.
Design by ValeraPerinski
$11.49Was $21.28
A bowl that looks coiled from rope, printed as one piece with the turns modelled into the wall. 5" across and 1.7" deep, with a flat base so it sits still - a fruit bowl or a key dish.
Design by JamesThePrinter
$8.43Was $15.62
A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published.
Design by Ian
$7.83Was $11.60
A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.
Design by Sitsero
$1.34Was $1.99
A tiny dragon printed as a chain of flexing segments, detailed all down its back and small enough to sit in two fingers. 3.0" long and only a few grams of plastic, printed in one piece.
Design by CrissyCat
$1.34Was $1.99
A lid that snaps onto a standard can and seals it up again between sips, and doubles as an opener when you slip it over the tab and tilt. It is the wider, support-free version, and it fits both the slim and the fat cans the designer built it around - European 202 cans, so if yours is a different can it is worth a quick measure. Light sanding on the slots is the only finishing it asks for.
Design by MakerShed
$3.72Was $6.88
An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.
$3.78Was $5.60
A dragon that prints in one piece with every plate of its body already jointed, so it coils and straightens straight off the bed - no supports, no assembly, and no loose parts. The spikes run the length of its back and read as armour when it is posed on a shelf. Three sizes: Small is 116 mm nose to tail, Medium is 140 mm and fits an A1 mini, and Large is 223 mm - the one that needs a full-size bed. The designer asks that anyone selling prints credit them and link the model page, which this listing does.
Design by CLUCKWORKS 3D
$1.34Was $2.26
A one-piece toy bow with a springy arrow that launches when you pull it back. Prints as a single piece with no assembly - ready to play with straight off the plate.
$15.39Was $28.50
A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim.
Design by DueMakers
$5.00Was $7.40
A snake printed in one piece with its body jointed along the whole of its length, so it coils and straightens as you play with it and holds whatever shape you leave it in. The scales run along its back and give it something to grip with. The designer prints it at 0.16 mm layers or finer at 100% scale, which is what keeps the joints free - print it coarser and it will come out stiff.
Design by Bash Studio 3D
$1.34Was $1.99
A dog's head that sits on top of a straw, ears up and nose forward.
Design by Morganja
$7.83Was $11.60
A star that opens and closes as you spin it: a print-in-place kinetic fidget with no assembly and no supports, so it comes off the plate ready to twist. Spinning it expands the arms from a closed cone into an open fan and back, which is the part that keeps hands busy, and it looks good parked on a desk either way. Best in a silk or colour-changing filament, which is what the designer recommends.
Design by Big-D-SyneS
$1.34Was $1.99
A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.
$1.44Was $2.66
A Jeep grille that rides on top of a straw, seven slots and all.
Design by Morganja
$1.34Was $1.99
A starfish printed as a chain of flexing segments, with five arms that trail and curl so it drapes over your hand. 4.5" across, printed in one piece with no supports.
Design by mieldeprot
$1.90Was $3.52
A baby dragon 3.9" long, printed in one piece. Two versions come off the plate: the flexi one is a chain of segments that curls and straightens in your hand, and the solid one is a single rigid body with the same shape. Pick which you want.
Design by Quantrex
$2.63Was $4.86
An articulated gecko 7.7" long, printed in one piece with every segment already moving - it curls over a shelf edge, drapes across a monitor and stays where you leave it. The plate also carries its little tongue.
Design by KrisCyber
$9.12Was $13.50
Four dinosaur cookie cutters with matching stamp inserts - press the stamp for the details, cut the outline, bake. Each cutter is about 3" across, and the set is four different animals.
Design by Merilno3D
$1.72Was $2.54
A clip-on egg separator: crack an egg into the channel and the white runs through while the yolk stays put. 3.6" long, printed in one piece, and it sits on the rim of a cup or a bowl.
Design by user_4069524941
$1.34Was $1.99
A 1:20 pallet, 50 by 55 mm, for an RC forklift or a shelf of scale freight. It prints with no supports and, at two walls with solid bottom layers, comes out solid through the body. The proportions follow a UK-style pallet rather than a North American one. Designed by CippyO and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by CippyO
$20.24Was $29.99
A 1/64 scale GP60B diesel for the Dragon Railway: the body, the bogies and the small fittings, printed across five plates, about 191 g of plastic in the set. It is a layout model rather than a toy that survives a floor, and RamBros publishes an assembly manual and a video covering the parts it wants. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by RamBros
$1.34Was $1.99
A bat whose wings are cut into linked segments, so they flex when it is handled and settle into a curve on a shelf - printed in one piece with every joint already free. 3.9" across the wingspan, about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Tybob24
$20.24Was $29.99
An arrow holder that takes up to twelve arrows, for shafts up to 11/32 of an inch across. One arrow or a dozen loaded on the same side, it stays upright, and it needs no supports; the designer printed his on an A1 mini. It is not a frugal print - the designer says so himself - so it is priced by what it weighs rather than by the pose. Designed by StickMan and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by StickMan
$4.17Was $6.17
A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.
Design by DanyP86
$4.46Was $6.60
A pinecone geocache: a hollow cone with a screw-on cap and a loop at the top for a string or a length of wire, so it can hang in a branch. It prints in two pieces and neither needs supports. For a cache that lives outdoors, PETG keeps its shape in a hot car or a sunny hedge better than PLA. Designed by Soalar, who remixed it from Izak02's Pine cone cache - both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Soalar
$1.34Was $1.99
A single autumn leaf, 3.7" x 4.3" and 3 mm thick, printed flat in one colour. It sits under a mug as a coaster, or scatters across a shelf or a table for the season. Shown as a render of the printable model, not a photograph.
Design by 3D-Print-Bunker
$1.34Was $1.99
A lid that presses onto an open drinks can and slides shut, keeping dust, wasps and debris out of a beer or a soda between sips. Two fits are on offer: the standard can, whose lid measures 1.4 by 1.9 inches, and a wider one at 1.5 by 2.4 inches for a fatter 16 oz rim. Each prints as a lid and its sliding cover, and the standard lid also comes in the designer's looser-fitting version for a can that runs tight. Designed by Tiger prints, who remixed EcoDad's Printables lid - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by Tiger prints
$20.24Was $29.99
A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Weso2976
$2.45Was $3.62
An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.
Design by IndigoRaptor
$7.38Was $10.93
A dalmatian sitting upright in low-poly facets, about five inches deep - a shelf or mantel piece that holds its shape from the side as well as the front. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.
Design by Creaitivity Studio
$13.88Was $20.56
A pair of little seated figures, each holding a round planter bowl - set them side by side on a windowsill with a succulent, a tea light or loose change in each cup. The two span 7.9" together and print from one file at about 103 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by cr_seb_olarte
$6.40Was $9.48
A collie lying down with its head on its paws, cut into low-poly facets and about four inches long. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.
Design by Creaitivity Studio
$10.12Was $14.99
A Saint Bernard sitting with its head up, cut into flat low-poly planes that read as fur from a distance and catch the light in a silk or metallic filament. About five inches deep, printed as one piece. The picture is a render of the printable model, not a photograph of a finished print.
Design by Creaitivity Studio
$1.34Was $1.99
A hook keeper that clips onto the rod handle and gives a lure somewhere to sit between casts, instead of swinging at the line. Three sizes, for rod handles of three diameters; the designer prints his in PETG and that is what the shop prints here, since this is a part that goes to the water. Designed by bambaxp and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.
Design by bambaxp
$3.62Was $5.36
A small Japandi-style vase: a rounded bulb wrapped in fine vertical ribs, narrowing to a small open neck, so a single stem stands upright in it. 3.1" tall across a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by oakliz27
$14.96Was $22.16
A high-detail ice dragon with its wings spread and its head raised, about five and a half inches across - a display piece rather than a toy, with the scale and wing membrane holding up close. Printed exactly as the designer published it. The picture is a render of the printable model, not a photograph of a finished print.
Design by ScourgePrints
$1.34Was $1.99
A can cap that opens the can as well: press it over the top of a standard 355 ml tab can and the drink is covered between sips, with the opener moulded into the same part. It prints in one piece in about forty minutes with no supports. Designed by BUD THE RETIRED PRINT GUY and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.
Design by BUD THE RETIRED PRINT GUY
$8.33Was $12.33
A pirate doubloon 45 mm across, with a skull and crossbones on the face and a beaded rim. The file prints fourteen on one plate, so it arrives as a small hoard - a treasure chest, a cake, a party favour or a handful for a costume. The picture is a render of the printable model, not a photograph of a finished print.
Design by Mike Coats
