The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.
Design by R3DPanda
A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.
Design by JSBallpython
A braid tool: hook the strands through the slot and the plait forms as you pull, so a French braid takes half the time and no third hand. 5.8" long, printed flat in one piece. Shown as a render, not a photo.
Design by Cy-Bea
A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.
Design by c4444
A ruler that folds: nineteen 160 mm segments that hinge end to end, plus the two end caps, so it measures a room and then folds down to a pocket. The full set is 19 segments; the smaller option is the same design at 70 per cent, which is the one for a desk drawer. Shown as a render, not a photo.
Design by PenguinPrototypes
Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.
Design by 3dprinting
The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.
Design by kot1199
A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.
Design by eclien
A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.
Design by Terrain 6
A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.
Design by inhabitworker
A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.
Design by Asky
A squeezer that slides up the tube as it empties: the roller presses the paste forward and the key at the end hooks over a rail so the tube hangs. 2.9" long, printed in one piece with the edges rounded so it does not catch on the shelf. Remixed by Weisnetde from two earlier squeezers, all under the same licence. Shown as a render, not a photo.
Design by Weisnetde
Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.
Design by Chilly_275
A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.
Design by blunt
A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.
Design by Jerryie
Two strands twisted around each other into a pen stand: a double helix about 22 cm tall on a 14 cm square base, printed in one piece with nothing to assemble. Pens drop into the gaps between the rungs and lean out along the twist, so a handful of them fan apart instead of clumping together in a cup - and the base is wide enough that a full stand does not tip. Empty, it is a desk ornament rather than a mug with pens in it, which is most of what a pen holder does all day. Printed in PLA at a 0.2 mm layer, about 34 g of plastic. Designed by AndreUser and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by AndreUser
The topsy tail tool: a loop on a stem that pulls a ponytail through itself, so you can make the flip without a second pair of hands. 7.0" long, printed flat in one piece. Shown as a render, not a photo.
Design by Cy-Bea
A pocket divot tool with a ball marker that sits in the handle: the fork lifts the green back into shape, the marker pops out to mark your line. 2.7" long, printed as two pieces. Shown as a render, not a photo.
Design by bitclicker
A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.
Design by pain.killer.2
A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.
Design by PanteraRuber