3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.

A clip-on egg separator: crack an egg into the channel and the white runs through while the yolk stays put. 3.6" long, printed in one piece, and it sits on the rim of a cup or a bowl.

Design by user_4069524941

A low-poly Labrador, faceted like cut stone, standing with its head up: the low-poly build keeps it light enough to print and lets it catch the light along the facets. Two sizes - the big one at 4.7" tall and a pup at 2.4" - each printed in one piece.

Design by CreaitivityStudio

Four dinosaur cookie cutters with matching stamp inserts - press the stamp for the details, cut the outline, bake. Each cutter is about 3" across, and the set is four different animals.

Design by Merilno3D

A skeleton printed as a chain of flexing segments, rib cage and all, so it dangles, swings and rattles about. 3.1" long, printed in one piece and only a few grams of plastic.

Design by Max

A skull with flat faceted planes rather than curves, with the top of the cranium hollowed out for a small plant or a succulent. 4.3" tall, printed in one piece - a Halloween pot that stays on the shelf in November.

Design by oakliz27

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim. Shown as a render, not a photo.

Design by DueMakers

Candle holders that let the light out through the walls: a Voronoi web of gaps and ridges so the flame - a battery tealight, never a real one - glows through the whole shell rather than out of the top. The set is three holders, three diffusers and the base plate that carries them; print the holders in matte black and the diffusers in white, which is the pairing the designer built it around, and a single holder works just as well on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A low-poly heart, faceted like cut stone: the low-poly build keeps it light and lets it catch the light along the facets, and it stands on its own on a shelf. 3.4" wide, printed in one piece. Shown as a render, not a photo.

Design by Creaitivity Studio

A little bear holding a heart, printed in one piece with the heart standing proud of its chest. Shown as a render, not a photo.

Design by davide7seven

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.

Design by NordicCreativa

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A pair of arrow earrings, each with a coiled shaft, a small loop at the tip for the hook and a heart-shaped flight. They print flat and weigh well under a gram for the pair, so they want hooks or studs fitted afterwards. Each is 2.1" by 0.7". Shown as a render, not a photo.

Design by TinkerTogether

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

A hockey cake topper: a player winding up over the words Happy Birthday, cut as one piece that stands in the cake. 6.5" x 7.8", about 16 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by NikaLand

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Astler

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by bigdobbo3D

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

Winter forest deer ornaments: three deer among trees, cut as flat silhouettes with a hole to hang each one. 3.4" each, about 21 g of plastic for the set of three. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Walter3D

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

A wolf in profile built from flat geometric planes: one piece, printed flat, for a wall or a desk stand. 7" x 4.3", about 5 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

A BMW E36 mid-drift, cut as a minimalist silhouette with the car sitting low and sideways. 7" x 5.4", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Kuba

A stag head in faceted planes, printed as one flat piece - a low-poly wall hanging in a single colour. 5.7" x 6.2", about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A ribbon Christmas tree with a bow: flat loops folded into a tree shape, with a hole at the top to hang it. 3.9" tall, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ababskia3D

A Christmas teddy bear: a bear in a Santa hat with a ribbon to hang it by, printed in two sizes. 2" or 3.1" tall, about 12 g and 40 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by raven.log

Two cats nose to nose with a heart between them, cut flat on a base - a table piece for Valentine's Day. 7.5" wide and about 41 g of plastic in two parts, which slot together. Shown as a render, not a photo.

Design by Olaf Dobrosielski

A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SuperBgr

The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Abz

An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Michel

A record sleeve stands on a ledge under a patterned back panel, and the ledge carries NOW PLAYING across its face in relief, so the record on the shelf is announced rather than guessed at. 200 mm wide and 159 mm tall - wide enough for a 12 inch sleeve - printed in one piece with no supports under the sign. Designed by Kosmok and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Kosmok

A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.

Design by thift88

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A square indoor planter with ruched, fabric-like sides and a clean flat rim, so it reads as a cloth-wrapped pot until you pick it up. It prints in PLA with a drainage hole in the base, and it is 4.7" wide by 3.9" tall. Shown as a render, not a photo.

Design by Dossi

A tall vase with a drop falling through its wall, and the tray that holds it: the designer made it for a single stem or a bundle of dried grass, and the tray catches whatever you drop in it, which is where the mindfulness comes in. Printed as two pieces - the vase and its holder - so you can use them together as an arrangement or keep the tray on a desk for rings, keys and incense. Standing 24 cm, it wants a shelf with headroom or the middle of a table. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A turtle small enough to sit on a shelf edge: the shell is modelled with its own scutes and the head, tail and legs are all there, so it reads as a real turtle rather than a toy one. 2.3" long and printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Type1Printing

A pair of leaf earrings: a pointed leaf with its veins cut into the face, light enough to wear all day at a bit over a gram the pair. They print flat with a hole at the top for the hook, so nothing else is needed but the ear wire. Each is 1.9" by 0.8". Shown as a render, not a photo.

Design by C4UStudio

One little ghost, three sizes of it: Small is 35 mm tall, Medium 45 mm and Large 64 mm, so a shelf can gather a few rather than carry a loner. Each prints as a rounded little spectre with a friendly face and no supports. Every ghost is its own object on the plate, so no multi-colour printer is needed - print them in different colours and they arrive as a set. The small one disappears into a bowl by the door; the large still fits in a hand. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A pair of open heart outlines, each about 1.9" by 1.6" and barely over a gram, with a small hole at the top for the ear wire. They print flat, so the outline stays crisp and there is nothing to finish beyond fitting the hooks. Shown as a render, not a photo.

Design by C4UStudio