3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.

A clip-on egg separator: crack an egg into the channel and the white runs through while the yolk stays put. 3.6" long, printed in one piece, and it sits on the rim of a cup or a bowl.

Design by user_4069524941

A low-poly Labrador, faceted like cut stone, standing with its head up: the low-poly build keeps it light enough to print and lets it catch the light along the facets. Two sizes - the big one at 4.7" tall and a pup at 2.4" - each printed in one piece.

Design by CreaitivityStudio

Four dinosaur cookie cutters with matching stamp inserts - press the stamp for the details, cut the outline, bake. Each cutter is about 3" across, and the set is four different animals.

Design by Merilno3D

A skeleton printed as a chain of flexing segments, rib cage and all, so it dangles, swings and rattles about. 3.1" long, printed in one piece and only a few grams of plastic.

Design by Max

A skull with flat faceted planes rather than curves, with the top of the cranium hollowed out for a small plant or a succulent. 4.3" tall, printed in one piece - a Halloween pot that stays on the shelf in November.

Design by oakliz27

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim. Shown as a render, not a photo.

Design by DueMakers

Candle holders that let the light out through the walls: a Voronoi web of gaps and ridges so the flame - a battery tealight, never a real one - glows through the whole shell rather than out of the top. The set is three holders, three diffusers and the base plate that carries them; print the holders in matte black and the diffusers in white, which is the pairing the designer built it around, and a single holder works just as well on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A low-poly heart, faceted like cut stone: the low-poly build keeps it light and lets it catch the light along the facets, and it stands on its own on a shelf. 3.4" wide, printed in one piece. Shown as a render, not a photo.

Design by Creaitivity Studio

A little bear holding a heart, printed in one piece with the heart standing proud of its chest. Shown as a render, not a photo.

Design by davide7seven

Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.

Design by porkac

A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.

Design by NordicCreativa

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A pair of arrow earrings, each with a coiled shaft, a small loop at the tip for the hook and a heart-shaped flight. They print flat and weigh well under a gram for the pair, so they want hooks or studs fitted afterwards. Each is 2.1" by 0.7". Shown as a render, not a photo.

Design by TinkerTogether

A two-prong hair pin that holds a bun without a single elastic - the forks flex, so it grips and then lets go. Two lengths: 4.5" for fine or shoulder-length hair and 5.9" for thick or long. Printed flat in one piece, in one colour or two. Shown as a render, not a photo.

Design by riverbed

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

A hockey cake topper: a player winding up over the words Happy Birthday, cut as one piece that stands in the cake. 6.5" x 7.8", about 16 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by NikaLand

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Astler

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by bigdobbo3D

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

Winter forest deer ornaments: three deer among trees, cut as flat silhouettes with a hole to hang each one. 3.4" each, about 21 g of plastic for the set of three. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Walter3D

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

A wolf in profile built from flat geometric planes: one piece, printed flat, for a wall or a desk stand. 7" x 4.3", about 5 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

A BMW E36 mid-drift, cut as a minimalist silhouette with the car sitting low and sideways. 7" x 5.4", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Kuba

A stag head in faceted planes, printed as one flat piece - a low-poly wall hanging in a single colour. 5.7" x 6.2", about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A ribbon Christmas tree with a bow: flat loops folded into a tree shape, with a hole at the top to hang it. 3.9" tall, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ababskia3D

A Christmas teddy bear: a bear in a Santa hat with a ribbon to hang it by, printed in two sizes. 2" or 3.1" tall, about 12 g and 40 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by raven.log

Two cats nose to nose with a heart between them, cut flat on a base - a table piece for Valentine's Day. 7.5" wide and about 41 g of plastic in two parts, which slot together. Shown as a render, not a photo.

Design by Olaf Dobrosielski

A pair of eighth notes, each an outline rather than a filled shape, so they stay light on the ear and catch the light along the stem. Each is 20 x 22.7 mm and 2 mm thick, with the hole in the note head for a hook, and they print mirrored so the two notes sit opposite each other. Shown as a render of the printable model, not a photograph.

Design by mikesak29

A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SuperBgr

The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Abz

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Michel

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A filigree arch: a curved band of scrollwork with the spaces cut right through, so it reads as lace from the front and sits like a crescent against the ear. Each is 26 x 34 mm and 2.3 mm thick with the hook tab at the top, and the pair is mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A door corner for Halloween: a cat with a knife, cut to sit over the corner of a doorframe and be read from across the room. 7.9 by 7.8 inches and 5 mm thick, it prints flat in about an hour with no supports, and a 0.6 mm nozzle is an option the designer mentions for a chunkier line. Designed by H & R 3D and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by H & R 3D

A bee with a rounded body, two wings standing off it and a hook hole at the head, printed as one piece at 25 x 29 mm. The body is domed rather than flat, so it reads as a bee from the side too, and it is light enough to wear all day. Order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by wally

A pair of sunglasses with the arms and a bridge moulded in, printed 2.5 mm thick and 32 mm across, with a hole in each arm for a hook. They are a joke that prints properly: the lenses are open, so the shape holds at this size and reads at a glance. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by Ian