3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Four dinosaur cookie cutters with matching stamp inserts - press the stamp for the details, cut the outline, bake. Each cutter is about 3" across, and the set is four different animals.

Design by Merilno3D

The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.

Design by R3DPanda

A clip-on egg separator: crack an egg into the channel and the white runs through while the yolk stays put. 3.6" long, printed in one piece, and it sits on the rim of a cup or a bowl.

Design by user_4069524941

A pair of thin earrings, each 1.4" x 1.6" and about 2 mm thick, so they print as one small plate in a couple of minutes and weigh almost nothing on your ears. The pair is one item - the price is for both. Shown as a render, not a photo.

Design by Vulcain

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

Four feather shapes, each printed twice so every design makes a mirrored pair: 60 mm long, 2 mm thick, with the barbs cut through so the feather is an outline and the quill shows. Printed flat with no supports. The plate holds all eight earrings - the whole set of four pairs - and they come in one colour. Shown as a render of the printable model, not a photograph.

Design by KameleonForge

A headband with a horn and two ears, 205 mm across and 6 mm thick, so it sits flat on the head and prints in one piece on the plate with nothing to glue. The band is a loop rather than a rigid arc, so it grips a child's head and an adult's. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A round spider web in a ring, with every strand cut through so the web is open and a spider sits in the middle of it. Each is about 44 x 48 mm and 2.2 mm thick, with a loop at the top for a hook, and both webs print together as one piece. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A headband in a soft wave, 157 mm across and printed in PETG the way its designer publishes it - PETG bends where PLA would snap, and a headband is a part that gets flexed every time it is worn. Designed by Elyse_ and released as Creative Commons Public Domain (CC0 1.0), so the prints may be sold with no condition attached. Shown as a render of the printable model, not a photograph.

Design by Elyse_

A watermelon slice with the rind standing proud of the flesh and the seeds cut into it, 26.7 x 25.9 mm and 1.6 mm thick with a hole at the top for a hook. The plate prints eight slices, which is four pairs; order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A butterfly with its wings open and the veins left raised, so the pattern survives printing instead of filling in. Each is 49 x 31 mm and 1.6 mm thick, thin enough to sit flat against the ear, with a hole at the top for a hook. The pair prints as two mirrored butterflies. Shown as a render of the printable model, not a photograph.

Design by FrazierSmith

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

A bee with a rounded body, two wings standing off it and a hook hole at the head, printed as one piece at 25 x 29 mm. The body is domed rather than flat, so it reads as a bee from the side too, and it is light enough to wear all day. Order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by wally

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A pair of eighth notes, each an outline rather than a filled shape, so they stay light on the ear and catch the light along the stem. Each is 20 x 22.7 mm and 2 mm thick, with the hole in the note head for a hook, and they print mirrored so the two notes sit opposite each other. Shown as a render of the printable model, not a photograph.

Design by mikesak29

A squeezer that slides up the tube as it empties: the roller presses the paste forward and the key at the end hooks over a rail so the tube hangs. 2.9" long, printed in one piece with the edges rounded so it does not catch on the shelf. Remixed by Weisnetde from two earlier squeezers, all under the same licence. Shown as a render, not a photo.

Design by Weisnetde

A Happy Birthday stencil for cakes and cookies: the words cut through a thin plate, so icing, cocoa or dusting sugar goes on through it. 3.9" wide, about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

Three holders that keep bottles lying down in the fridge instead of rolling out of the door - each cradles one bottle on its side and stacks with the others. The plate prints three, and each is about 9.4" long. Shown as a render, not a photo.

Design by RossMacAllan

A bowl for rinsing rice: the water swirls through the grain and pours off the side while the rice stays put, so you stop losing half of it down the sink. Two sizes - 6.9" across and a smaller 4.8" - each printed in one piece, with the drain holes and the pouring lip part of the bowl. Shown as a render, not a photo.

Design by ValeraPerinski

A race medal with a moulded ribbon and a numbered disc in the middle. The file holds first, second and third, so a set covers a whole podium for a school race or a party game. The picture is a render of the printable model, not a photograph of a finished print.

Design by Rodrigo Ferriz

A 2 mm PLA cake stencil, 6 x 4 inches, with Happy Birthday and three balloons cut right through. The lettering is a stencil face, so the middles of the a, p, B, R and D stay attached to the plaque instead of falling out. Lay it on a sheet of parchment over the cake, dust with cocoa or icing sugar, and lift it away. Four or more come at the bulk rate. The picture is a render of the printable model, not a photograph; real photos go up once the first one is printed.

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A braid tool: hook the strands through the slot and the plait forms as you pull, so a French braid takes half the time and no third hand. 5.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

A bag clip shaped like a cat, with a spring jaw that holds a chip bag or a coffee pouch shut. 1.6" across, printed in place in one piece - the hinge comes off the plate already working. Shown as a render, not a photo.

Design by Muuurt

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A pocket divot tool with a ball marker that sits in the handle: the fork lifts the green back into shape, the marker pops out to mark your line. 2.7" long, printed as two pieces. Shown as a render, not a photo.

Design by bitclicker

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.

Design by Merilno3D

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by eclien

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

A Christmas cookie stamp and its matching cutter: press the stamp into the dough and the outline cuts clean around it, so the icing has a line to follow. 3.1" across, printed as two pieces - stamp and cutter. Shown as a render, not a photo.

Design by P2T

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

A ruler that folds: nineteen 160 mm segments that hinge end to end, plus the two end caps, so it measures a room and then folds down to a pocket. The full set is 19 segments; the smaller option is the same design at 70 per cent, which is the one for a desk drawer. Shown as a render, not a photo.

Design by PenguinPrototypes

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting