3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.

Design by R3DPanda

A skeleton with print-in-place hinges at the shoulders, hips and knees, so the arms and legs swing as it moves and it settles back into a dangle when it stops. It prints as one piece with no supports and no assembly, 44 mm long, with a hole through the skull for a hook. Order a pair and you get two skeletons. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own.

Design by tomo3D

An arrow holder that takes up to twelve arrows, for shafts up to 11/32 of an inch across. One arrow or a dozen loaded on the same side, it stays upright, and it needs no supports; the designer printed his on an A1 mini. It is not a frugal print - the designer says so himself - so it is priced by what it weighs rather than by the pose. Designed by StickMan and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by StickMan

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

A squeezer that slides up the tube as it empties: the roller presses the paste forward and the key at the end hooks over a rail so the tube hangs. 2.9" long, printed in one piece with the edges rounded so it does not catch on the shelf. Remixed by Weisnetde from two earlier squeezers, all under the same licence. Shown as a render, not a photo.

Design by Weisnetde

A pocket divot tool with a ball marker that sits in the handle: the fork lifts the green back into shape, the marker pops out to mark your line. 2.7" long, printed as two pieces. Shown as a render, not a photo.

Design by bitclicker

A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by eclien

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting

The topsy tail tool: a loop on a stem that pulls a ponytail through itself, so you can make the flip without a second pair of hands. 7.0" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

A ruler that folds: nineteen 160 mm segments that hinge end to end, plus the two end caps, so it measures a room and then folds down to a pocket. The full set is 19 segments; the smaller option is the same design at 70 per cent, which is the one for a desk drawer. Shown as a render, not a photo.

Design by PenguinPrototypes

A hinged box for rings and earrings, 150 by 83 by 20 mm closed: a tray with compartments, a lid that shuts on printed hinges, and two pins that press in to hold the hinge line - four printed parts, no screws, no supports. Small enough for a wash bag and rigid enough to keep its shape. A remix of "Parametric hinged small parts box" by Billiam on Printables, which is CC BY 4.0, and designed by Ivan Chamberlain under Creative Commons Attribution 4.0 (CC BY 4.0) - both are credited. Shown as a render of the printable model, not a photograph.

Design by Ivan Chamberlain

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

Two strands twisted around each other into a pen stand: a double helix about 22 cm tall on a 14 cm square base, printed in one piece with nothing to assemble. Pens drop into the gaps between the rungs and lean out along the twist, so a handful of them fan apart instead of clumping together in a cup - and the base is wide enough that a full stand does not tip. Empty, it is a desk ornament rather than a mug with pens in it, which is most of what a pen holder does all day. Printed in PLA at a 0.2 mm layer, about 34 g of plastic. Designed by AndreUser and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AndreUser

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A headband with a horn and two ears, 205 mm across and 6 mm thick, so it sits flat on the head and prints in one piece on the plate with nothing to glue. The band is a loop rather than a rigid arc, so it grips a child's head and an adult's. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A headband in a soft wave, 157 mm across and printed in PETG the way its designer publishes it - PETG bends where PLA would snap, and a headband is a part that gets flexed every time it is worn. Designed by Elyse_ and released as Creative Commons Public Domain (CC0 1.0), so the prints may be sold with no condition attached. Shown as a render of the printable model, not a photograph.

Design by Elyse_

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.

Design by Merilno3D

A two-prong hair pin that holds a bun without a single elastic - the forks flex, so it grips and then lets go. Two lengths: 4.5" for fine or shoulder-length hair and 5.9" for thick or long. Printed flat in one piece, in one colour or two. Shown as a render, not a photo.

Design by riverbed

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.

Design by porkac

A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.

Design by inhabitworker

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A braid tool: hook the strands through the slot and the plait forms as you pull, so a French braid takes half the time and no third hand. 5.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A pair of eighth notes, each an outline rather than a filled shape, so they stay light on the ear and catch the light along the stem. Each is 20 x 22.7 mm and 2 mm thick, with the hole in the note head for a hook, and they print mirrored so the two notes sit opposite each other. Shown as a render of the printable model, not a photograph.

Design by mikesak29

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A heart drawn in a few asymmetric arcs, 34 x 29 mm and 2.3 mm thick, with a hole at the top for a hook. The plate is a solid rim around a cut-out centre, so it reads as a sketch of a heart rather than a filled one, and the pair hangs light. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

Two flip flops printed as one piece, each with a raised strap and a toe post standing up through the sole, so they read as sandals rather than flat outlines. Each is about 30 mm long with a hole at the heel for a hook, and the pair comes off the plate together. Shown as a render of the printable model, not a photograph.

Design by tomo3D

XO in solid letters, 40 x 37 mm and 2 mm thick, with a small hole at the base of the O for a hook. The two letters are cut as one piece, so each earring hangs as a single word rather than two separate charms. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by SynneLuna

A butterfly with its wings open and the veins left raised, so the pattern survives printing instead of filling in. Each is 49 x 31 mm and 1.6 mm thick, thin enough to sit flat against the ear, with a hole at the top for a hook. The pair prints as two mirrored butterflies. Shown as a render of the printable model, not a photograph.

Design by FrazierSmith

A santa hat with the tip curling over: the brim is a raised band, the crown is domed and the tip hangs past the brim, so the shape reads from the side as well as the front. Each hat is 23.8 x 15.3 mm and 5.5 mm tall with a hole through the crown for a hook, and the plate prints six of them, which is three pairs. Shown as a render of the printable model, not a photograph.

Design by Ettore

A six-fold filigree snowflake, 35 x 31 mm and 1.5 mm thick, with a hole at the top for a hook. Every branch is openwork, so it prints as fine line after fine line rather than a solid plate, and it catches the light as it moves. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by PediMR

A bee with a rounded body, two wings standing off it and a hook hole at the head, printed as one piece at 25 x 29 mm. The body is domed rather than flat, so it reads as a bee from the side too, and it is light enough to wear all day. Order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by wally

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

A dolphin inside an oval ring, 42 x 37 mm and 2.6 mm thick, with a small eyelet at the top for a hook. The dolphin is cut clear of the ring behind it, so the two shapes read separately and the pair hangs as two clean outlines. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Ghost1975w

A pair of sunglasses with the arms and a bridge moulded in, printed 2.5 mm thick and 32 mm across, with a hole in each arm for a hook. They are a joke that prints properly: the lenses are open, so the shape holds at this size and reads at a glance. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A watermelon slice with the rind standing proud of the flesh and the seeds cut into it, 26.7 x 25.9 mm and 1.6 mm thick with a hole at the top for a hook. The plate prints eight slices, which is four pairs; order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

Six hearts on one plate: a large pair at 31 x 28 mm and two smaller pairs at 12 x 11 mm and 10 x 9 mm, each with a smiling face and a hole for a hook. Sold as a set of three pairs - the large hearts for everyday, the two small pairs for a second piercing or to give away. Shown as a render of the printable model, not a photograph.

Design by Merche