The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.
Design by R3DPanda
A clip that holds a cable or a rope flat against a wall, in three sizes for different thicknesses. Each one is two parts that snap together - no supports, no screws - and the file prints all three sizes on one plate.
Design by GiskardReventlov
A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.
Design by inhabitworker
A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.
Design by Jerryie
A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.
Design by Jyffen
Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.
Design by adnamantino
A record sleeve stands on a ledge under a patterned back panel, and the ledge carries NOW PLAYING across its face in relief, so the record on the shelf is announced rather than guessed at. 200 mm wide and 159 mm tall - wide enough for a 12 inch sleeve - printed in one piece with no supports under the sign. Designed by Kosmok and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Kosmok
A strip that threads onto a guitar strap and holds a stack of picks, so a fresh one is within reach in the middle of a song: 100 mm long and 25 mm wide, printed in one piece. It sits on the strap rather than in a pocket, which is where picks go to be lost. Designed by willywidget and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by willywidget
An LP on the wall: a back plate with a shelf the cover stands on and two brackets that hold the record upright in front of it, so the sleeve and the disc are both on show. 218 by 214 mm and 187 mm deep, printed as one piece. Designed by LucMonnom and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.
Design by LucMonnom
A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.
Design by jakub.fousek97
Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.
Design by jdormer9
A zip tie you can undo: printed in place with the pawl already free, so it locks, releases and locks again. 5.6" long, about 1.5 g, and it replaces the one-use ties on a cable bundle. Shown as a render, not a photo.
Design by 3DPrintHub
A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.
Design by Jerryie
Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.
Design by 3dprinting
A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.
Design by IvanChamberlain
A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.
Design by Terrain 6
Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.
Design by Chilly_275
A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by gareth7562
A rail that a CD jewel case stands in, ribbed along its length so the case leans back instead of sliding forward, on four short feet that keep the disc off the shelf. 149 mm wide and 30 mm tall - the width of a standard case, with a little room either side. Designed by ToToKia and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.
Design by ToToKia
Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by SF3DPrints
A practice mute for trombone, printed in three parts: the long tapered body that goes down into the bell, the flared cup that caps it, and the small collar that keeps the two together. 250 mm long and 193 mm across the cup, so it takes a full-size bell. The cup is what does the muting, so the horn can be played in an apartment without the neighbours learning the set list. Designed by 烤肉大师 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by 烤肉大师
A capo in two printed parts: a jaw that sits across the strings and the lever that clamps it down, 92 mm wide so it spans a standard six-string fretboard. It goes on the neck above the fret and holds the strings at the new position, which is what lets one shape be played in any key. Designed by Kevdev, a remix of the Guitar Capo by HarleyPrints, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Kevdev
A plate of music notes cut flat at 3 mm: single quavers, beamed pairs, a dotted note and the odd small rest, from 25 mm up to 67 mm long, so a wall, a noticeboard or the front of a piano can be dressed with them. They print lying down, which means no supports and a clean face straight off the plate. Designed by EcneNomma and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by EcneNomma
A plectrum printed flat at half a millimetre, 27 mm tall and 24 mm across, with the designer's design across the face - the pun in the name is the whole idea. Thin picks bend more than thick ones, so this is the one for strumming rather than for shredding. Designed by marshal.meacham and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by marshal.meacham
A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.
Design by jakub.fousek97
A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.
Design by Clément Vasseneix
