The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.
Design by R3DPanda
A skeleton printed as a chain of flexing segments, rib cage and all, so it dangles, swings and rattles about. 3.1" long, printed in one piece and only a few grams of plastic.
Design by Max
A skull with flat faceted planes rather than curves, with the top of the cranium hollowed out for a small plant or a succulent. 4.3" tall, printed in one piece - a Halloween pot that stays on the shelf in November.
Design by oakliz27
A clip that holds a cable or a rope flat against a wall, in three sizes for different thicknesses. Each one is two parts that snap together - no supports, no screws - and the file prints all three sizes on one plate.
Design by GiskardReventlov
A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.
Design by Jerryie
Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.
Design by 3dprinting
A spider that sits in the top corner of a door frame, printed flat and 4 mm thick so it reads as a silhouette against the wall. 6.9" tall, printed in one piece with no supports - a corner of tape holds it, and it comes down without a mark. Shown as a render, not a photo.
Design by Ned's Designs
A bat with its wings wrapped forward, holding a tealight between them - the light spills out under the wings and throws the shape on the table. 5.5" tall, printed in one piece. Shown as a render, not a photo.
Design by Marlborke
A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.
Design by Jyffen
Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.
Design by jdormer9
A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.
Design by jakub.fousek97
A skeleton pinned flat and printed 3.7 mm thick, 6.9" tall - it hangs on a wall or a door and throws a proper outline, and it stacks flat in a box the other eleven months. Shown as a render, not a photo.
Design by TheModelAgency
A cat curled asleep inside a pumpkin, its back and tail proud of the shell - a Halloween piece about four inches wide that reads as one object until you are close enough to see the cat. Prints as one piece. The picture is a render of the printable model, not a photograph of a finished print.
Design by digidihey
A ghost with its hands over its face and a sheet that pools at the bottom, printed in one piece. Four sizes, from a 1.8" one for a windowsill to a 7.3" one that takes a shelf on its own. Shown as a render, not a photo.
Design by skuda3
A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.
Design by inhabitworker
A skeleton with print-in-place hinges at the shoulders, hips and knees, so the arms and legs swing as it moves and it settles back into a dangle when it stops. It prints as one piece with no supports and no assembly, 44 mm long, with a hole through the skull for a hook. Order a pair and you get two skeletons. Shown as a render of the printable model, not a photograph.
Design by tomo3D
A pumpkin cut into an open voronoi lattice, with a separate stem that sits in the top. The file also holds a second body with no base, if you would rather drop a tealight inside and let the shell glow through the gaps. Two pieces. The picture is a render of the printable model, not a photograph of a finished print.
Design by Mosselini1
A Halloween silhouette cut as one flat piece, 7" wide - the sort of thing you stand on a shelf or blu-tack to a window, and it reads from across a room. Printed flat in one piece, no supports. Shown as a render, not a photo.
Design by jwgnall
A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.
Design by Clément Vasseneix
A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.
Design by IvanChamberlain
A round spider web in a ring, with every strand cut through so the web is open and a spider sits in the middle of it. Each is about 44 x 48 mm and 2.2 mm thick, with a loop at the top for a hook, and both webs print together as one piece. Shown as a render of the printable model, not a photograph.
Design by tomo3D
A tower of ghost faces stacked one above the next, each turned a little further round than the last, about four and a half inches tall - a Halloween table piece that reads from across a room. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.
Design by Thinkspace
Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.
Design by adnamantino
A zip tie you can undo: printed in place with the pawl already free, so it locks, releases and locks again. 5.6" long, about 1.5 g, and it replaces the one-use ties on a cable bundle. Shown as a render, not a photo.
Design by 3DPrintHub
A pumpkin with the face cut right through, so a tealight inside throws the grin onto the wall rather than just glowing. 3.9" tall, printed in one piece - drop a battery tealight in the base and it lights the whole face. Shown as a render, not a photo.
Design by PentillyCrafts
A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.
Design by Terrain 6
A hand rising out of the ground with its fingers curled around a candle - the fingers grip an LED tealight, so the light comes out between them. 5.2" across, printed in one piece; a 46 mm version for a bigger candle is on file. Shown as a render, not a photo.
Design by PentillyCrafts
Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.
Design by Chilly_275
A bat cut as one flat piece that folds along its wings, so it hangs from a thread and moves with the air rather than sitting rigid. 7.4" across, printed flat with no supports and a fraction under 10 g. Shown as a render, not a photo.
Design by M.Sima
A small ghost holding a tealight: the flame glows through the shell and out of the eyes, so the whole figure lights up. 3" tall, about 12 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by BeninManc
A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.
Design by Jerryie
