3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published.

Design by Ian

A clip that holds a cable or a rope flat against a wall, in three sizes for different thicknesses. Each one is two parts that snap together - no supports, no screws - and the file prints all three sizes on one plate.

Design by GiskardReventlov

One small fox, about 1.7" tall and 1.9" long, head up with its thick tail curled along its side. The designer's plate carries twenty-five copies of this fox, and the listing is for ONE of them - add as many as you want. The plate prints in one go with no supports and no AMS, which is what it was built for.

Design by AkeStudio

A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.

Design by Sitsero

A bowl that looks coiled from rope, printed as one piece with the turns modelled into the wall. 5" across and 1.7" deep, with a flat base so it sits still - a fruit bowl or a key dish.

Design by JamesThePrinter

The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.

Design by R3DPanda

A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.

A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim.

Design by DueMakers

An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.

A low-poly vase built from big flat facets that twist as they rise, so light catches every plane differently. 5.5" across its widest and 3.9" tall, printed in one piece.

Design by Harry

A guide that keeps a garden hose off the flowers: the hose runs through the roller and the stake holds it where you want it, so dragging it round a corner stops flattening the bed. 4.7" tall, printed as a body and a stake. Shown as a render, not a photo.

Design by Tulmuz

A sitting baby elephant with its trunk curled up and its ears out, printed in one piece with no supports. 2.4" tall, and about 9 g of plastic, so it sits on a shelf or a desk without a base. Shown as a render, not a photo.

Design by user_1541493983

A zip tie you can undo: printed in place with the pawl already free, so it locks, releases and locks again. 5.6" long, about 1.5 g, and it replaces the one-use ties on a cable bundle. Shown as a render, not a photo.

Design by 3DPrintHub

A dragon egg with scales cut over the whole shell and a lid that lifts off, so it hides something small. Three sizes: 1.4", 2.8" and 3.7" tall, the big one weighing about 50 g. Printed in one piece, lid and all. Shown as a render, not a photo.

Design by Type1Printing

A dragon in a coiled pose, wings half-open and tail curling round to its head - a display piece rather than a toy. 9.5" across and the biggest thing on the shelf, printed in one piece. Shown as a render, not a photo.

Design by mdesign

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.

Design by NordicCreativa

A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.

Design by ZHeights

A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.

Design by UncleFlappy

A square indoor planter with ruched, fabric-like sides and a clean flat rim, so it reads as a cloth-wrapped pot until you pick it up. It prints in PLA with a drainage hole in the base, and it is 4.7" wide by 3.9" tall. Shown as a render, not a photo.

Design by Dossi

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A modular hydroponic tower printed as twelve parts: a base, the column that stacks, five growing cups and the plates that close the sides. The column is 220 mm across and 128 mm tall, each cup 55 mm. The modules come apart, so a tower can be built one section at a time and taken down again. Shown as a render of the printable model, not a photograph.

Design by user_139533078

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A three-part seed germinator - base, insert and lid - 4.5" x 5.5" and 20 mm deep, printed in whatever colour you pick. Shown as a render of the printable model, not a photograph.

Design by 3dmonios

A mosquito trap that uses a jar you already have: a funnel that drops into a mason jar's mouth, so a jar of water and a spoon of sugar becomes a trap. The cone lets a mosquito in and the jar's own walls keep it there. Three funnels come off the plate, 76 mm across and 47 mm tall, for the jar sizes the designer covered - standard jam jars among them. Designed by IanFoulds, a remix of the Mosquito Trap by Urasxman, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by IanFoulds

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A large arched tunnel for a vivarium: a rock-textured hide that a reptile or amphibian can walk through and sleep in. 7.9" long, about 256 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by VivariumVisions

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Michel

A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SuperBgr

A vortex vase whose wall spirals in one continuous swirl from base to off-centre mouth, so it looks like it is still turning. 5.4" tall over a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.

Design by inhabitworker

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

Four miniature garden tools - shovel, spade, pitchfork and rake - about 2.8" long, with the hafts and heads modelled properly rather than blobs. A set for a dollhouse garden, a terrarium or a plant shelf. Shown as a render, not a photo.

Design by Gekon3D

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.

Design by thift88

A flat-pack stand for holding earrings: a base plate, two uprights and a crossbar that slot into each other, with the uprights stepped so pairs hang at different heights instead of bunching. Assembled it is about 170 x 100 mm and stands 13 mm deep, big enough for a shelf or a dresser top. It prints as four flat pieces with no supports and comes to about 83 g of plastic. Shown as a render of the printable model, not a photograph.

Design by Recflying

A butterfly drawn as one continuous line and cut 1.5 mm thick at 150 x 160 mm, so it sits on a wall as a shape that casts a shadow rather than a solid plaque. It prints flat in one piece with no supports and needs no fixings: mounting putty or a pin behind the body is enough. Shown as a render of the printable model, not a photograph.

Design by PediM