3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Showing 1-9 of 9 products

Coaster Leafs
25% offBulk deal 4+
from $6.57Was: $8.76$5.91 each with 4+ in a $30 orderDetails

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

Coaster Leafs

Earrings 060
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A pair of thin earrings, each 1.4" x 1.6" and about 2 mm thick, so they print as one small plate in a couple of minutes and weigh almost nothing on your ears. The pair is one item - the price is for both. Shown as a render, not a photo.

Design by Vulcain

Earrings 060

Two Prong French Hair Pin
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A two-prong hair pin that holds a bun without a single elastic - the forks flex, so it grips and then lets go. Two lengths: 4.5" for fine or shoulder-length hair and 5.9" for thick or long. Printed flat in one piece, in one colour or two. Shown as a render, not a photo.

Design by riverbed

Two Prong French Hair Pin

French Braid Hairstyle Tool
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A braid tool: hook the strands through the slot and the plait forms as you pull, so a French braid takes half the time and no third hand. 5.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

French Braid Hairstyle Tool

Napkin Holder
25% offBulk deal 4+
from $11.90Was: $15.86$10.71 each with 4+ in a $30 orderDetails

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

Napkin Holder

Hair Topsy Tail Tool
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

The topsy tail tool: a loop on a stem that pulls a ponytail through itself, so you can make the flip without a second pair of hands. 7.0" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

Hair Topsy Tail Tool

Ring Size Measuring Set
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.

Design by porkac

Ring Size Measuring Set

Voronoi Napkin Holder
25% offBulk deal 4+
from $3.41Was: $4.54$3.07 each with 4+ in a $30 orderDetails

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

Voronoi Napkin Holder

Sea Napkin Rings
25% offBulk deal 4+
from $9.78Was: $13.04$8.80 each with 4+ in a $30 orderDetails

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

Sea Napkin Rings