3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.

A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim.

Design by DueMakers

A low-poly vase built from big flat facets that twist as they rise, so light catches every plane differently. 5.5" across its widest and 3.9" tall, printed in one piece.

Design by Harry

A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.

Design by NordicCreativa

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A square indoor planter with ruched, fabric-like sides and a clean flat rim, so it reads as a cloth-wrapped pot until you pick it up. It prints in PLA with a drainage hole in the base, and it is 4.7" wide by 3.9" tall. Shown as a render, not a photo.

Design by Dossi

A guide that keeps a garden hose off the flowers: the hose runs through the roller and the stake holds it where you want it, so dragging it round a corner stops flattening the bed. 4.7" tall, printed as a body and a stake. Shown as a render, not a photo.

Design by Tulmuz

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

Four miniature garden tools - shovel, spade, pitchfork and rake - about 2.8" long, with the hafts and heads modelled properly rather than blobs. A set for a dollhouse garden, a terrarium or a plant shelf. Shown as a render, not a photo.

Design by Gekon3D

A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.

Design by DanyP86

A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.

Design by pain.killer.2

A pair of little seated figures, each holding a round planter bowl - set them side by side on a windowsill with a succulent, a tea light or loose change in each cup. The two span 7.9" together and print from one file at about 103 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by cr_seb_olarte

A small Japandi-style vase: a rounded bulb wrapped in fine vertical ribs, narrowing to a small open neck, so a single stem stands upright in it. 3.1" tall across a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

A vortex vase whose wall spirals in one continuous swirl from base to off-centre mouth, so it looks like it is still turning. 5.4" tall over a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

A mosquito trap that uses a jar you already have: a funnel that drops into a mason jar's mouth, so a jar of water and a spoon of sugar becomes a trap. The cone lets a mosquito in and the jar's own walls keep it there. Three funnels come off the plate, 76 mm across and 47 mm tall, for the jar sizes the designer covered - standard jam jars among them. Designed by IanFoulds, a remix of the Mosquito Trap by Urasxman, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by IanFoulds

A three-part seed germinator - base, insert and lid - 4.5" x 5.5" and 20 mm deep, printed in whatever colour you pick. Shown as a render of the printable model, not a photograph.

Design by 3dmonios

A modular hydroponic tower printed as twelve parts: a base, the column that stacks, five growing cups and the plates that close the sides. The column is 220 mm across and 128 mm tall, each cup 55 mm. The modules come apart, so a tower can be built one section at a time and taken down again. Shown as a render of the printable model, not a photograph.

Design by user_139533078

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt