32% offClearance · only 3 left!
$1.34Details
A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.
3D-printed products and 3MF downloads from Roxium in Burlington, Ontario
32% offBulk deal 4+
$7.83Details
A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.
Design by Sitsero
Puffer Jacket Pencil Holder
32% offBulk deal 4+
$1.34Details
A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.
Design by PrintcessJacqueline3DDesigns
Ghost Bookmark
32% offBulk deal 4+
$1.34Details
A pair of thin earrings, each 1.4" x 1.6" and about 2 mm thick, so they print as one small plate in a couple of minutes and weigh almost nothing on your ears. The pair is one item - the price is for both. Shown as a render, not a photo.
Design by Vulcain
Earrings 060
32% offBulk deal 4+
$1.34Details
A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.
Design by fgiancarelli
Friendly Reading Guide
32% offBulk deal 4+
$11.69Details
A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.
Design by mikan
Archimedean Solid (Tube)
32% offBulk deal 4+
$2.15Details
The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.
Design by kot1199
Multiplication Table 2-9
32% offBulk deal 4+
$18.78Details
A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.
Design by euro100xx
Vulcan Volcano
32% offBulk deal 4+
$28.29Details
A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.
Design by osamutake
Educational Gear Examples
32% offBulk deal 4+
$1.34Details
A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.
Design by Forged in Filament
Short Sword Bookmark
32% offBulk deal 4+
$11.98Details
A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.
Design by Asky
Microscope Slide Box
32% offBulk deal 4+
$1.34Details
A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.
Design by Merilno3D
Petal Flower Stencil
32% offBulk deal 4+
$3.07Details
A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.
Design by IvanChamberlain
Voronoi Napkin Holder
32% offBulk deal 4+
$8.06Details
Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.
Design by Merilno3D
Tree Music Brick Stencil Set
32% offBulk deal 4+
$5.91Details
Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.
Design by jdormer9
Coaster Leafs
32% offBulk deal 4+
$1.34Details
A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.
Design by UncleFlappy
Simple T-Rex Dinosaur Bookmark
32% offBulk deal 4+
$7.86Details
A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.
Design by ZHeights
Book Tracker Sign
32% offBulk deal 4+
$10.71Details
A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.
Design by Jyffen
Napkin Holder
32% offBulk deal 4+
$8.80Details
Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.
Design by adnamantino
Sea Napkin Rings
32% offBulk deal 4+
$1.34Details
Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.
Design by porkac