3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.

A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.

Design by Sitsero

A lid that snaps onto a standard can and seals it up again between sips, and doubles as an opener when you slip it over the tab and tilt. It is the wider, support-free version, and it fits both the slim and the fat cans the designer built it around - European 202 cans, so if yours is a different can it is worth a quick measure. Light sanding on the slots is the only finishing it asks for.

Design by MakerShed

Four dinosaur cookie cutters with matching stamp inserts - press the stamp for the details, cut the outline, bake. Each cutter is about 3" across, and the set is four different animals.

Design by Merilno3D

A clip-on egg separator: crack an egg into the channel and the white runs through while the yolk stays put. 3.6" long, printed in one piece, and it sits on the rim of a cup or a bowl.

Design by user_4069524941

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A dog's head that sits on top of a straw, ears up and nose forward. Shown as a render, not a photo.

Design by Morganja

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A Jeep grille that rides on top of a straw, seven slots and all. Shown as a render, not a photo.

Design by Morganja

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A stag head in faceted planes, printed as one flat piece - a low-poly wall hanging in a single colour. 5.7" x 6.2", about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.

Design by thift88

A BMW E36 mid-drift, cut as a minimalist silhouette with the car sitting low and sideways. 7" x 5.4", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Kuba

A wolf in profile built from flat geometric planes: one piece, printed flat, for a wall or a desk stand. 7" x 4.3", about 5 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by bigdobbo3D

Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Astler

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A dragon egg with overlapping scales and a lid that lifts off, so it hides something small inside. 2.4" tall, printed in one piece - the shell and the lid come off the plate together. Shown as a render, not a photo.

Design by LLucas404

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

A single autumn leaf, 3.7" x 4.3" and 3 mm thick, printed flat in one colour. It sits under a mug as a coaster, or scatters across a shelf or a table for the season. Shown as a render of the printable model, not a photograph.

Design by 3D-Print-Bunker

A flower on a stem that stands on its own - the petals print as one piece with the stalk, so it needs no water and no vase. 3.9" tall, and the stem is a separate file if you want a different height. Shown as a render, not a photo.

Design by JarJar

Three holders that keep bottles lying down in the fridge instead of rolling out of the door - each cradles one bottle on its side and stacks with the others. The plate prints three, and each is about 9.4" long. Shown as a render, not a photo.

Design by RossMacAllan

A collie lying down with its head on its paws, cut into low-poly facets and about four inches long. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A bowl for rinsing rice: the water swirls through the grain and pours off the side while the rice stays put, so you stop losing half of it down the sink. Two sizes - 6.9" across and a smaller 4.8" - each printed in one piece, with the drain holes and the pouring lip part of the bowl. Shown as a render, not a photo.

Design by ValeraPerinski

A pirate doubloon 45 mm across, with a skull and crossbones on the face and a beaded rim. The file prints fourteen on one plate, so it arrives as a small hoard - a treasure chest, a cake, a party favour or a handful for a costume. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mike Coats

A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.

Design by AmandaRoos

Twenty-five foxes, each about 1.7" tall and no two the same pose - sitting, curled, walking, looking up. The whole plate prints in one go with no supports and no AMS, which is what the designer built it for: a shelf of foxes from a single print. Shown as a render, not a photo.

Design by AkeStudio

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D