3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Showing 1-9 of 9 products

Golf Divot Tool
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A pocket divot tool with a ball marker that sits in the handle: the fork lifts the green back into shape, the marker pops out to mark your line. 2.7" long, printed as two pieces. Shown as a render, not a photo.

Design by bitclicker

Golf Divot Tool

Golf Tee
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by LilÕJimbob

Golf Tee

Voronoi Napkin Holder
25% offBulk deal 4+
from $3.41Was: $4.54$3.07 each with 4+ in a $30 orderDetails

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

Voronoi Napkin Holder

Coaster Leafs
25% offBulk deal 4+
from $6.57Was: $8.76$5.91 each with 4+ in a $30 orderDetails

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

Coaster Leafs

Napkin Holder
25% offBulk deal 4+
from $11.90Was: $15.86$10.71 each with 4+ in a $30 orderDetails

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

Napkin Holder

Ring Size Measuring Set
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.

Design by porkac

Ring Size Measuring Set

Earrings 060
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A pair of thin earrings, each 1.4" x 1.6" and about 2 mm thick, so they print as one small plate in a couple of minutes and weigh almost nothing on your ears. The pair is one item - the price is for both. Shown as a render, not a photo.

Design by Vulcain

Earrings 060

Double Ended Fish Hook Removal Tool
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by eclien

Double Ended Fish Hook Removal Tool

Sea Napkin Rings
25% offBulk deal 4+
from $9.78Was: $13.04$8.80 each with 4+ in a $30 orderDetails

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

Sea Napkin Rings