A skeleton printed as a chain of flexing segments, rib cage and all, so it dangles, swings and rattles about. 3.1" long, printed in one piece and only a few grams of plastic.
Design by Max
A skull with flat faceted planes rather than curves, with the top of the cranium hollowed out for a small plant or a succulent. 4.3" tall, printed in one piece - a Halloween pot that stays on the shelf in November.
Design by oakliz27
A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.
Design by eclien
A ghost with its hands over its face and a sheet that pools at the bottom, printed in one piece. Four sizes, from a 1.8" one for a windowsill to a 7.3" one that takes a shelf on its own. Shown as a render, not a photo.
Design by skuda3
A small ghost holding a tealight: the flame glows through the shell and out of the eyes, so the whole figure lights up. 3" tall, about 12 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by BeninManc
A pocket divot tool with a ball marker that sits in the handle: the fork lifts the green back into shape, the marker pops out to mark your line. 2.7" long, printed as two pieces. Shown as a render, not a photo.
Design by bitclicker
A hand rising out of the ground with its fingers curled around a candle - the fingers grip an LED tealight, so the light comes out between them. 5.2" across, printed in one piece; a 46 mm version for a bigger candle is on file. Shown as a render, not a photo.
Design by PentillyCrafts
A cat curled asleep inside a pumpkin, its back and tail proud of the shell - a Halloween piece about four inches wide that reads as one object until you are close enough to see the cat. Prints as one piece. The picture is a render of the printable model, not a photograph of a finished print.
Design by digidihey
A spider that sits in the top corner of a door frame, printed flat and 4 mm thick so it reads as a silhouette against the wall. 6.9" tall, printed in one piece with no supports - a corner of tape holds it, and it comes down without a mark. Shown as a render, not a photo.
Design by Ned's Designs
A bat cut as one flat piece that folds along its wings, so it hangs from a thread and moves with the air rather than sitting rigid. 7.4" across, printed flat with no supports and a fraction under 10 g. Shown as a render, not a photo.
Design by M.Sima
A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by LilÕJimbob
A tower of ghost faces stacked one above the next, each turned a little further round than the last, about four and a half inches tall - a Halloween table piece that reads from across a room. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.
Design by Thinkspace
A Halloween silhouette cut as one flat piece, 7" wide - the sort of thing you stand on a shelf or blu-tack to a window, and it reads from across a room. Printed flat in one piece, no supports. Shown as a render, not a photo.
Design by jwgnall
A pumpkin cut into an open voronoi lattice, with a separate stem that sits in the top. The file also holds a second body with no base, if you would rather drop a tealight inside and let the shell glow through the gaps. Two pieces. The picture is a render of the printable model, not a photograph of a finished print.
Design by Mosselini1
A pumpkin with the face cut right through, so a tealight inside throws the grin onto the wall rather than just glowing. 3.9" tall, printed in one piece - drop a battery tealight in the base and it lights the whole face. Shown as a render, not a photo.
Design by PentillyCrafts
A bat with its wings wrapped forward, holding a tealight between them - the light spills out under the wings and throws the shape on the table. 5.5" tall, printed in one piece. Shown as a render, not a photo.
Design by Marlborke
A skeleton pinned flat and printed 3.7 mm thick, 6.9" tall - it hangs on a wall or a door and throws a proper outline, and it stacks flat in a box the other eleven months. Shown as a render, not a photo.
Design by TheModelAgency