3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A skeleton printed as a chain of flexing segments, rib cage and all, so it dangles, swings and rattles about. 3.1" long, printed in one piece and only a few grams of plastic.

Design by Max

A skull with flat faceted planes rather than curves, with the top of the cranium hollowed out for a small plant or a succulent. 4.3" tall, printed in one piece - a Halloween pot that stays on the shelf in November.

Design by oakliz27

A round spider web in a ring, with every strand cut through so the web is open and a spider sits in the middle of it. Each is about 44 x 48 mm and 2.2 mm thick, with a loop at the top for a hook, and both webs print together as one piece. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A squeezer that slides up the tube as it empties: the roller presses the paste forward and the key at the end hooks over a rail so the tube hangs. 2.9" long, printed in one piece with the edges rounded so it does not catch on the shelf. Remixed by Weisnetde from two earlier squeezers, all under the same licence. Shown as a render, not a photo.

Design by Weisnetde

A small ghost holding a tealight: the flame glows through the shell and out of the eyes, so the whole figure lights up. 3" tall, about 12 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A cat curled asleep inside a pumpkin, its back and tail proud of the shell - a Halloween piece about four inches wide that reads as one object until you are close enough to see the cat. Prints as one piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A pumpkin with the face cut right through, so a tealight inside throws the grin onto the wall rather than just glowing. 3.9" tall, printed in one piece - drop a battery tealight in the base and it lights the whole face. Shown as a render, not a photo.

Design by PentillyCrafts

A skeleton with print-in-place hinges at the shoulders, hips and knees, so the arms and legs swing as it moves and it settles back into a dangle when it stops. It prints as one piece with no supports and no assembly, 44 mm long, with a hole through the skull for a hook. Order a pair and you get two skeletons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A ghost with its hands over its face and a sheet that pools at the bottom, printed in one piece. Four sizes, from a 1.8" one for a windowsill to a 7.3" one that takes a shelf on its own. Shown as a render, not a photo.

Design by skuda3

A bat cut as one flat piece that folds along its wings, so it hangs from a thread and moves with the air rather than sitting rigid. 7.4" across, printed flat with no supports and a fraction under 10 g. Shown as a render, not a photo.

Design by M.Sima

A bat with its wings wrapped forward, holding a tealight between them - the light spills out under the wings and throws the shape on the table. 5.5" tall, printed in one piece. Shown as a render, not a photo.

Design by Marlborke

A hand rising out of the ground with its fingers curled around a candle - the fingers grip an LED tealight, so the light comes out between them. 5.2" across, printed in one piece; a 46 mm version for a bigger candle is on file. Shown as a render, not a photo.

Design by PentillyCrafts

A Halloween silhouette cut as one flat piece, 7" wide - the sort of thing you stand on a shelf or blu-tack to a window, and it reads from across a room. Printed flat in one piece, no supports. Shown as a render, not a photo.

Design by jwgnall

A skeleton pinned flat and printed 3.7 mm thick, 6.9" tall - it hangs on a wall or a door and throws a proper outline, and it stacks flat in a box the other eleven months. Shown as a render, not a photo.

Design by TheModelAgency

A spider that sits in the top corner of a door frame, printed flat and 4 mm thick so it reads as a silhouette against the wall. 6.9" tall, printed in one piece with no supports - a corner of tape holds it, and it comes down without a mark. Shown as a render, not a photo.

Design by Ned's Designs

A tower of ghost faces stacked one above the next, each turned a little further round than the last, about four and a half inches tall - a Halloween table piece that reads from across a room. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Thinkspace

A pumpkin cut into an open voronoi lattice, with a separate stem that sits in the top. The file also holds a second body with no base, if you would rather drop a tealight inside and let the shell glow through the gaps. Two pieces. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mosselini1

A teepee that holds the spare rolls: two printed panels hinged into a tent, a base that keeps it square and three dowels that peg it together, with a roll inside. 6" across and 5.3" tall, printed in panels and assembled - the modular system, in the size that fits a small printer. Shown as a render, not a photo.

Design by ThePhilosopher