3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.

The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.

Design by R3DPanda

A clip that holds a cable or a rope flat against a wall, in three sizes for different thicknesses. Each one is two parts that snap together - no supports, no screws - and the file prints all three sizes on one plate.

Design by GiskardReventlov

A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim. Shown as a render, not a photo.

Design by DueMakers

A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.

Design by NordicCreativa

A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.

Design by inhabitworker

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A square indoor planter with ruched, fabric-like sides and a clean flat rim, so it reads as a cloth-wrapped pot until you pick it up. It prints in PLA with a drainage hole in the base, and it is 4.7" wide by 3.9" tall. Shown as a render, not a photo.

Design by Dossi

A guide that keeps a garden hose off the flowers: the hose runs through the roller and the stake holds it where you want it, so dragging it round a corner stops flattening the bed. 4.7" tall, printed as a body and a stake. Shown as a render, not a photo.

Design by Tulmuz

A zip tie you can undo: printed in place with the pawl already free, so it locks, releases and locks again. 5.6" long, about 1.5 g, and it replaces the one-use ties on a cable bundle. Shown as a render, not a photo.

Design by 3DPrintHub

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

Four miniature garden tools - shovel, spade, pitchfork and rake - about 2.8" long, with the hafts and heads modelled properly rather than blobs. A set for a dollhouse garden, a terrarium or a plant shelf. Shown as a render, not a photo.

Design by Gekon3D

A low-poly vase built from big flat facets that twist as they rise, so light catches every plane differently. 5.5" across its widest and 3.9" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Harry

A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.

Design by DanyP86

A pair of little seated figures, each holding a round planter bowl - set them side by side on a windowsill with a succulent, a tea light or loose change in each cup. The two span 7.9" together and print from one file at about 103 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by cr_seb_olarte

A small Japandi-style vase: a rounded bulb wrapped in fine vertical ribs, narrowing to a small open neck, so a single stem stands upright in it. 3.1" tall across a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

A vortex vase whose wall spirals in one continuous swirl from base to off-centre mouth, so it looks like it is still turning. 5.4" tall over a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

A mosquito trap that uses a jar you already have: a funnel that drops into a mason jar's mouth, so a jar of water and a spoon of sugar becomes a trap. The cone lets a mosquito in and the jar's own walls keep it there. Three funnels come off the plate, 76 mm across and 47 mm tall, for the jar sizes the designer covered - standard jam jars among them. Designed by IanFoulds, a remix of the Mosquito Trap by Urasxman, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by IanFoulds

A three-part seed germinator - base, insert and lid - 4.5" x 5.5" and 20 mm deep, printed in whatever colour you pick. Shown as a render of the printable model, not a photograph.

Design by 3dmonios

A modular hydroponic tower printed as twelve parts: a base, the column that stacks, five growing cups and the plates that close the sides. The column is 220 mm across and 128 mm tall, each cup 55 mm. The modules come apart, so a tower can be built one section at a time and taken down again. Shown as a render of the printable model, not a photograph.

Design by user_139533078

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt