A gyro fidget spinner: three curved rings interlock around a centre post and whirl as one, so it prints in a single piece with no bearings and no assembly - just flick it and go. The rings are loose in their track out of the printer, which is the part that takes a few tries to get right and the reason this one gets measured before it ships.
Two spirals in one print: an outer shell that twists one way and a core that twists the other, turning past each other as you fiddle. Printed in a single colour it reads as one tapering cone; give the shell and the core a colour each and the two spirals separate in the eye as they turn, which is what the designer's own pictures show. The profile that prints it is 0.2 mm layers, 3 walls, 15 per cent gyroid infill, PLA, no supports, standing upright exactly as supplied.
Design by NerdHerder
A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by M_LAB
A clicker keychain with four buttons that press and click, printed in place so nothing needs assembling. Shown as a render, not a photo.
Design by Print3DFamilyFidgets
A star that spins: the points are cut so it turns on its axis in the hand and keeps turning. Shown as a render, not a photo.
Design by CreaitivityStudio
A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.
Design by eclien
A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.
Design by JSBallpython
A hexagonal tube cut into one continuous spiral, so it springs and flexes in the hand and the turns of the helix roll past each other under a thumb. It prints as a single piece and needs no assembly, and it stands 2.8" tall by 1.3" across. Shown as a render, not a photo.
Design by NerdHerder
A desk caddy printed in one piece: a raised back that stands a phone at a reading angle, a round well for pens, and a square tray for a watch, keys or a card, with a slot for a charging cable to pass through. It is 7.1" wide by 3.5" deep. Shown as a render, not a photo.
Design by Maker76
A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.
Design by Katejot2017
A planetary gear set printed in place: six small gears mesh between a sun gear and a toothed ring, so turning any one of them turns all the rest. It is 2.5" across and prints as a single piece with nothing to snap together. Shown as a render, not a photo.
Design by HurtTree
Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.
Design by PenguinPrototypes
A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.
Design by LangHjornArt
A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.
Design by Elaak
Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Astler
An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by bigdobbo3D
A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Peppino
A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.
Design by Jyffen
A wolf in profile built from flat geometric planes: one piece, printed flat, for a wall or a desk stand. 7" x 4.3", about 5 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Peppino
Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.
Design by adnamantino
A BMW E36 mid-drift, cut as a minimalist silhouette with the car sitting low and sideways. 7" x 5.4", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Kuba
A large arched tunnel for a vivarium: a rock-textured hide that a reptile or amphibian can walk through and sleep in. 7.9" long, about 256 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by VivariumVisions
A stag head in faceted planes, printed as one flat piece - a low-poly wall hanging in a single colour. 5.7" x 6.2", about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Peppino
An impossible passthrough wound as a spiral: the helical parts turn through each other and hold, printed in one piece. 2.8" tall, about 29 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by BeninManc
An impossible passthrough built as a pyramid: the parts pass through one another and no amount of turning lets them go. 2.8" tall, about 21 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by BeninManc
A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by MoltenPlastic3D
A stackable glasses stand: a fin that the cradles slide onto, so the tower grows to whatever height the collection needs. The cradles come in three widths - 67, 77 and 87 mm - and each holds one pair nose-down by the bridge, which suits slim readers and deep sunglass frames alike. The plate prints a whole tower's worth of parts, 167 by 199 mm laid out as the designer arranges it. Designed by Badger Sound Forge and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.
Design by Badger Sound Forge
A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by SuperBgr
The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.
Design by Abz
An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Michel
A modular glasses stand: a round 143 mm base with a spindle, a post that carries two long arms, and a cradle that stacks on the spindle, so two pairs or a shelf-full can be kept upright and out of the way. The arms take frames by the bridge and the base is heavy enough not to tip when one pair comes off. Designed by Rockthered and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by Rockthered
A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.
Design by Ian
A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.
Design by thift88
A fidget spinner small enough to live in a pocket: one piece, no bearings, no axle to glue, printed in place so the two halves and their weights come off the plate ready to spin. It is a 15-minute print in the designer's own profile, which is why it makes a good giveaway or market-stock item. Printed in a silk filament the spinning face catches the light. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by DragonFusion3D
A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.
Design by user_3738174853
Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.
A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.
Design by Print3DFamilyFidgets
A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.
Design by TinkerTogether
An inner cone passes right through an outer one and neither of them comes apart - that is the whole trick, and it prints as a single piece. Roll it in your hands and the two bodies slide past each other, which is the part that keeps fingers busy. Printed in two colours the cones separate in the eye and the pass-through reads as impossible; printed in one it looks like a solid cone until it moves. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by What3d
A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.
Design by ArmadilloFDM
A phone stand that folds out of a keychain: the plate swings up and the phone leans back on it, and folded away it hangs on your keys. Shown as a render, not a photo.
Design by musielovsky
A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.
Design by MakerShed
A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.
Design by UKSTL
Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.
Design by jdormer9
A bowl that looks coiled from rope, printed as one piece with the turns modelled into the wall. 5" across and 1.7" deep, with a flat base so it sits still - a fruit bowl or a key dish. Shown as a render, not a photo.
Design by JamesThePrinter
A frog that jumps: press its back and it springs off the table, and the pond bowl catches it. Pick the frog on its own or the bowl with it - the bowl is 5" across, and three frogs fit on one plate if you want a set. Shown as a render, not a photo.
Design by Niski
Twenty-five foxes, each about 1.7" tall and no two the same pose - sitting, curled, walking, looking up. The whole plate prints in one go with no supports and no AMS, which is what the designer built it for: a shelf of foxes from a single print. Shown as a render, not a photo.
Design by AkeStudio
A hard hat that goes on a keyring - the dome, the brim and the little ridge down the middle, printed in one piece with a hole through the top. 1.5" across, and it works as a key tag or a desk charm. Shown as a render, not a photo.
Design by astavr
