3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published.

Design by Ian

One small fox, about 1.7" tall and 1.9" long, head up with its thick tail curled along its side. The designer's plate carries twenty-five copies of this fox, and the listing is for ONE of them - add as many as you want. The plate prints in one go with no supports and no AMS, which is what it was built for.

Design by AkeStudio

Two spirals in one print: an outer shell that twists one way and a core that twists the other, turning past each other as you fiddle. Printed in a single colour it reads as one tapering cone; give the shell and the core a colour each and the two spirals separate in the eye as they turn, which is what the designer's own pictures show. The profile that prints it is 0.2 mm layers, 3 walls, 15 per cent gyroid infill, PLA, no supports, standing upright exactly as supplied.

Design by NerdHerder

An impossible passthrough built as a pyramid: the parts pass through one another and no amount of turning lets them go. 2.8" tall, about 21 g of plastic.

Design by BeninManc

An impossible passthrough shaped like an hourglass: two halves that turn through each other and stay locked together. 2.8" tall, about 24 g of plastic.

Design by BeninManc

A bowl that looks coiled from rope, printed as one piece with the turns modelled into the wall. 5" across and 1.7" deep, with a flat base so it sits still - a fruit bowl or a key dish.

Design by JamesThePrinter

A hard hat that goes on a keyring - the dome, the brim and the little ridge down the middle, printed in one piece with a hole through the top. 1.5" across, and it works as a key tag or a desk charm.

Design by astavr

A gyro fidget spinner: three curved rings interlock around a centre post and whirl as one, so it prints in a single piece with no bearings and no assembly - just flick it and go. The rings are loose in their track out of the printer, which is the part that takes a few tries to get right and the reason this one gets measured before it ships.

A sitting baby elephant with its trunk curled up and its ears out, printed in one piece with no supports. 2.4" tall, and about 9 g of plastic, so it sits on a shelf or a desk without a base. Shown as a render, not a photo.

Design by user_1541493983

A dragon egg with scales cut over the whole shell and a lid that lifts off, so it hides something small. Three sizes: 1.4", 2.8" and 3.7" tall, the big one weighing about 50 g. Printed in one piece, lid and all. Shown as a render, not a photo.

Design by Type1Printing

A dragon in a coiled pose, wings half-open and tail curling round to its head - a display piece rather than a toy. 9.5" across and the biggest thing on the shelf, printed in one piece. Shown as a render, not a photo.

Design by mdesign

A hexagonal tube cut into one continuous spiral, so it springs and flexes in the hand and the turns of the helix roll past each other under a thumb. It prints as a single piece and needs no assembly, and it stands 2.8" tall by 1.3" across. Shown as a render, not a photo.

Design by NerdHerder

A frog that jumps: press its back and it springs off the table, and the pond bowl catches it. Pick the frog on its own or the bowl with it - the bowl is 5" across, and three frogs fit on one plate if you want a set. Shown as a render, not a photo.

Design by Niski

A ruler that folds: nineteen 160 mm segments that hinge end to end, plus the two end caps, so it measures a room and then folds down to a pocket. The full set is 19 segments; the smaller option is the same design at 70 per cent, which is the one for a desk drawer. Shown as a render, not a photo.

Design by PenguinPrototypes

A desk caddy printed in one piece: a raised back that stands a phone at a reading angle, a round well for pens, and a square tray for a watch, keys or a card, with a slot for a charging cable to pass through. It is 7.1" wide by 3.5" deep. Shown as a render, not a photo.

Design by Maker76

A planetary gear set printed in place: six small gears mesh between a sun gear and a toothed ring, so turning any one of them turns all the rest. It is 2.5" across and prints as a single piece with nothing to snap together. Shown as a render, not a photo.

Design by HurtTree

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

An inner cone passes right through an outer one and neither of them comes apart - that is the whole trick, and it prints as a single piece. Roll it in your hands and the two bodies slide past each other, which is the part that keeps fingers busy. Printed in two colours the cones separate in the eye and the pass-through reads as impossible; printed in one it looks like a solid cone until it moves. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by What3d

A stackable glasses stand: a fin that the cradles slide onto, so the tower grows to whatever height the collection needs. The cradles come in three widths - 67, 77 and 87 mm - and each holds one pair nose-down by the bridge, which suits slim readers and deep sunglass frames alike. The plate prints a whole tower's worth of parts, 167 by 199 mm laid out as the designer arranges it. Designed by Badger Sound Forge and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Badger Sound Forge

A modular glasses stand: a round 143 mm base with a spindle, a post that carries two long arms, and a cradle that stacks on the spindle, so two pairs or a shelf-full can be kept upright and out of the way. The arms take frames by the bridge and the base is heavy enough not to tip when one pair comes off. Designed by Rockthered and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Rockthered

A phone stand that folds out of a keychain: the plate swings up and the phone leans back on it, and folded away it hangs on your keys. Shown as a render, not a photo.

Design by musielovsky

The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Abz

A fidget spinner small enough to live in a pocket: one piece, no bearings, no axle to glue, printed in place so the two halves and their weights come off the plate ready to spin. It is a 15-minute print in the designer's own profile, which is why it makes a good giveaway or market-stock item. Printed in a silk filament the spinning face catches the light. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DragonFusion3D

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

Two strands twisted around each other into a pen stand: a double helix about 22 cm tall on a 14 cm square base, printed in one piece with nothing to assemble. Pens drop into the gaps between the rungs and lean out along the twist, so a handful of them fan apart instead of clumping together in a cup - and the base is wide enough that a full stand does not tip. Empty, it is a desk ornament rather than a mug with pens in it, which is most of what a pen holder does all day. Printed in PLA at a 0.2 mm layer, about 34 g of plastic. Designed by AndreUser and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AndreUser

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

An impossible passthrough wound as a spiral: the helical parts turn through each other and hold, printed in one piece. 2.8" tall, about 29 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A large arched tunnel for a vivarium: a rock-textured hide that a reptile or amphibian can walk through and sleep in. 7.9" long, about 256 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by VivariumVisions

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Michel

A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SuperBgr

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A pen holder clad in raised dragon scales, hexagonal all the way round, with a smooth inner cup for pens, pencils or brushes. 3.1" across and 4" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3DWoosh

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A top that keeps going: a heavy rim, a fine point and a printed handle to spin it between finger and thumb. 2.1" across, about 41 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by happybirthday

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444