3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

An articulated dragonfly: the body and each wing are cut into flat segments joined by print-in-place hinges, so it flexes in the hand and settles back flat when you set it down. It prints as one piece with no supports, 4" across by 2.7".

Design by Tybob24

A cube of eight hinged blocks that folds in on itself: twist it one way and it turns inside out, fold it the other and it closes back into a cube, which is the whole trick and the reason one stays on a desk. It prints as a single piece with its hinges already in place, in two sizes, and needs no supports or assembly.

Design by Print3DFamily

A crocodile printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles and curls in your hand. 4.0" long, printed in one piece.

Design by ThePrintDrawer

A hard hat that goes on a keyring - the dome, the brim and the little ridge down the middle, printed in one piece with a hole through the top. 1.5" across, and it works as a key tag or a desk charm.

Design by astavr

A slug that ripples: the body is a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. About 3.0" curled, printed in one piece with no supports. Enlarged and remixed by yusuffles from matveymoo's "Curled up Friendly Slug", and sold under the same share-alike licence.

Design by yusuffles

A lucky toad, printed in one piece with no supports, about 1.9" across and 2" tall with its little belly. Four come at the bulk rate.

Design by Ake Studio

A monster printed as a chain of flexing segments - horns, a ridge of spines down its back and a tail that curls - so it stands up, slumps and wriggles. 3.9" tall, printed in one piece with no supports, in one colour or three.

Design by TinkerLink

One small fox, about 1.7" tall and 1.9" long, head up with its thick tail curled along its side. The designer's plate carries twenty-five copies of this fox, and the listing is for ONE of them - add as many as you want. The plate prints in one go with no supports and no AMS, which is what it was built for.

Design by AkeStudio

A bowl that looks coiled from rope, printed as one piece with the turns modelled into the wall. 5" across and 1.7" deep, with a flat base so it sits still - a fruit bowl or a key dish.

Design by JamesThePrinter

A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published.

Design by Ian

An impossible passthrough shaped like an hourglass: two halves that turn through each other and stay locked together. 2.8" tall, about 24 g of plastic.

Design by BeninManc

An impossible passthrough built as a pyramid: the parts pass through one another and no amount of turning lets them go. 2.8" tall, about 21 g of plastic.

Design by BeninManc

A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.

Design by Sitsero

A tiny dragon printed as a chain of flexing segments, detailed all down its back and small enough to sit in two fingers. 3.0" long and only a few grams of plastic, printed in one piece.

Design by CrissyCat

Two spirals in one print: an outer shell that twists one way and a core that twists the other, turning past each other as you fiddle. Printed in a single colour it reads as one tapering cone; give the shell and the core a colour each and the two spirals separate in the eye as they turn, which is what the designer's own pictures show. The profile that prints it is 0.2 mm layers, 3 walls, 15 per cent gyroid infill, PLA, no supports, standing upright exactly as supplied.

Design by NerdHerder

A dragon that prints in one piece with every plate of its body already jointed, so it coils and straightens straight off the bed - no supports, no assembly, and no loose parts. The spikes run the length of its back and read as armour when it is posed on a shelf. Three sizes: Small is 116 mm nose to tail, Medium is 140 mm and fits an A1 mini, and Large is 223 mm - the one that needs a full-size bed. The designer asks that anyone selling prints credit them and link the model page, which this listing does.

Design by CLUCKWORKS 3D

A one-piece toy bow with a springy arrow that launches when you pull it back. Prints as a single piece with no assembly - ready to play with straight off the plate.

A snake printed in one piece with its body jointed along the whole of its length, so it coils and straightens as you play with it and holds whatever shape you leave it in. The scales run along its back and give it something to grip with. The designer prints it at 0.16 mm layers or finer at 100% scale, which is what keeps the joints free - print it coarser and it will come out stiff.

Design by Bash Studio 3D

A star that opens and closes as you spin it: a print-in-place kinetic fidget with no assembly and no supports, so it comes off the plate ready to twist. Spinning it expands the arms from a closed cone into an open fan and back, which is the part that keeps hands busy, and it looks good parked on a desk either way. Best in a silk or colour-changing filament, which is what the designer recommends.

Design by Big-D-SyneS

A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.

A gyro fidget spinner: three curved rings interlock around a centre post and whirl as one, so it prints in a single piece with no bearings and no assembly - just flick it and go. The rings are loose in their track out of the printer, which is the part that takes a few tries to get right and the reason this one gets measured before it ships.

A starfish printed as a chain of flexing segments, with five arms that trail and curl so it drapes over your hand. 4.5" across, printed in one piece with no supports.

Design by mieldeprot

A baby dragon 3.9" long, printed in one piece. Two versions come off the plate: the flexi one is a chain of segments that curls and straightens in your hand, and the solid one is a single rigid body with the same shape. Pick which you want.

Design by Quantrex

An articulated gecko 7.7" long, printed in one piece with every segment already moving - it curls over a shelf edge, drapes across a monitor and stays where you leave it. The plate also carries its little tongue.

Design by KrisCyber

A 1:20 pallet, 50 by 55 mm, for an RC forklift or a shelf of scale freight. It prints with no supports and, at two walls with solid bottom layers, comes out solid through the body. The proportions follow a UK-style pallet rather than a North American one. Designed by CippyO and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by CippyO

A 1/64 scale GP60B diesel for the Dragon Railway: the body, the bogies and the small fittings, printed across five plates, about 191 g of plastic in the set. It is a layout model rather than a toy that survives a floor, and RamBros publishes an assembly manual and a video covering the parts it wants. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A bat whose wings are cut into linked segments, so they flex when it is handled and settle into a curve on a shelf - printed in one piece with every joint already free. 3.9" across the wingspan, about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Tybob24

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

A single autumn leaf, 3.7" x 4.3" and 3 mm thick, printed flat in one colour. It sits under a mug as a coaster, or scatters across a shelf or a table for the season. Shown as a render of the printable model, not a photograph.

Design by 3D-Print-Bunker

A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Weso2976

An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.

Design by IndigoRaptor

A dalmatian sitting upright in low-poly facets, about five inches deep - a shelf or mantel piece that holds its shape from the side as well as the front. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A collie lying down with its head on its paws, cut into low-poly facets and about four inches long. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A Saint Bernard sitting with its head up, cut into flat low-poly planes that read as fur from a distance and catch the light in a silk or metallic filament. About five inches deep, printed as one piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A high-detail ice dragon with its wings spread and its head raised, about five and a half inches across - a display piece rather than a toy, with the scale and wing membrane holding up close. Printed exactly as the designer published it. The picture is a render of the printable model, not a photograph of a finished print.

Design by ScourgePrints

A pirate doubloon 45 mm across, with a skull and crossbones on the face and a beaded rim. The file prints fourteen on one plate, so it arrives as a small hoard - a treasure chest, a cake, a party favour or a handful for a costume. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mike Coats

A beaver balanced on its tail, built from an open voronoi lattice: solid from across the room, a web of struts up close, and it catches the light in a silk or metallic filament. One piece, and it stands on its own. Mosselini1 rebuilt the voronoi beaver and this is that remix. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mosselini1

A baby dragon that prints in one piece, with an articulated spine so the neck, wings and tail all bend and the whole thing can drape over a finger. It sits, curls and lies down, and needs no assembly and no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Helios3D

A desk golf set in eleven printed pieces: a green you can rearrange piece by piece, a ball, a club and the furniture around it. About 3" a piece and 115 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SakiSale

A giraffe lying down with its neck folded back and its legs tucked - printed as a chain of segments, so it flops about when you pick it up. 6.5" long, and the eyes print as separate 8 mm pieces that go in after. Shown as a render, not a photo.

Design by SHF3D.

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

A dragon curled asleep on a bed of autumn leaves, small enough for a desk or a windowsill. Printed in a single colour with no AMS needed, so it comes off the plate ready to sit. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A dobermann sitting to attention in flat low-poly planes: ears up, chest forward, about four inches tall. One piece, no supports, and the facets suit a matte or metallic filament. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A mushroom charm in three pieces that press together: a domed cap, the gills under it and a stem with fixing pegs. Printing it in parts lets the cap take one colour and the stem another, and the assembled charm is about 23 mm tall and 13 mm across with a hole in the cap for a hook. Shown as a render of the printable model, not a photograph.

Design by iNkosi3D

A butterfly drawn as one continuous line and cut 1.5 mm thick at 150 x 160 mm, so it sits on a wall as a shape that casts a shadow rather than a solid plaque. It prints flat in one piece with no supports and needs no fixings: mounting putty or a pin behind the body is enough. Shown as a render of the printable model, not a photograph.

Design by PediM