3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A tall fluted vase, 209 mm high and 79 mm across, printed in vase mode with a single wall so a light behind it shows the ribs. The designer also publishes a two-wall profile if you want it to hold water - say so when ordering and the shop will run that one instead. Designed by Ian and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published.

Design by Ian

One small fox, about 1.7" tall and 1.9" long, head up with its thick tail curled along its side. The designer's plate carries twenty-five copies of this fox, and the listing is for ONE of them - add as many as you want. The plate prints in one go with no supports and no AMS, which is what it was built for.

Design by AkeStudio

A pair of arrow earrings, each with a coiled shaft, a small loop at the tip for the hook and a heart-shaped flight. They print flat and weigh well under a gram for the pair, so they want hooks or studs fitted afterwards. Each is 2.1" by 0.7". The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own.

Design by TinkerTogether

A Spartan helmet in profile, crest and all, 2.2" tall, with a loop at the top so it hangs as a pendant or swings on a keyring. It prints flat in one piece, which keeps the crest and the cheek guard crisp.

Design by OrangeSs

A low-poly Labrador, faceted like cut stone, standing with its head up: the low-poly build keeps it light enough to print and lets it catch the light along the facets. Two sizes - the big one at 4.7" tall and a pup at 2.4" - each printed in one piece.

Design by CreaitivityStudio

A bowl that looks coiled from rope, printed as one piece with the turns modelled into the wall. 5" across and 1.7" deep, with a flat base so it sits still - a fruit bowl or a key dish.

Design by JamesThePrinter

A one-piece beard comb with rounded teeth that glide through without scraping. Small enough to live in a jacket pocket, and it prints without supports. The solid band above the teeth can carry a name, cut into the surface rather than raised, because a comb lives in a pocket and raised letters are the first thing to wear off: type the name while you are adding it to the cart, up to 12 characters, +$5. A personalized comb is cut to order, so it is paid online rather than reserved for cash at pickup. Leave it blank and it comes exactly as the photos show it.

A crowned lion head with a loop at the top, about four inches tall - a pendant, a bag charm or a wall ornament, with the mane and crown cut deep enough to hold a highlight. One piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

A sitting baby elephant with its trunk curled up and its ears out, printed in one piece with no supports. 2.4" tall, and about 9 g of plastic, so it sits on a shelf or a desk without a base. Shown as a render, not a photo.

Design by user_1541493983

A 2 mm PLA cake stencil, 6 x 4 inches, with Happy Birthday and three balloons cut right through. The lettering is a stencil face, so the middles of the a, p, B, R and D stay attached to the plaque instead of falling out. Lay it on a sheet of parchment over the cake, dust with cocoa or icing sugar, and lift it away. Four or more come at the bulk rate. The picture is a render of the printable model, not a photograph; real photos go up once the first one is printed.

A dragon egg with scales cut over the whole shell and a lid that lifts off, so it hides something small. Three sizes: 1.4", 2.8" and 3.7" tall, the big one weighing about 50 g. Printed in one piece, lid and all. Shown as a render, not a photo.

Design by Type1Printing

A dragon in a coiled pose, wings half-open and tail curling round to its head - a display piece rather than a toy. 9.5" across and the biggest thing on the shelf, printed in one piece. Shown as a render, not a photo.

Design by mdesign

Mark the shark as a keychain or as a necklace charm - the same shark in two fittings, one with a ring hole and one sized for a chain. It prints flat with no supports, about 2.4" long. Shown as a render, not a photo.

Design by dominator334

Four Jeep charms, each a different model cut in relief and each with a hole at the top for a keyring or a chain. Pick the one you want - they print flat with no supports and measure about 2.4" by 2.4". Shown as a render, not a photo.

Design by dominator334

The classic folded awareness ribbon with a keyring loop at the top, printed flat so the fold reads cleanly on both faces. It is 2.5" long by 1.4" wide and prints in whatever colour you choose. Shown as a render, not a photo.

Design by Miss3DP

Five heart shapes, each layered front to back so the colours read as depth: black sits at the back as the outline and the two layers in front are yours to choose, so one colour is the simplest and three makes it pop. Pick the shape you want - each is about 1.6" by 1.5", with a loop for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A tall vase with a drop falling through its wall, and the tray that holds it: the designer made it for a single stem or a bundle of dried grass, and the tray catches whatever you drop in it, which is where the mindfulness comes in. Printed as two pieces - the vase and its holder - so you can use them together as an arrangement or keep the tray on a desk for rings, keys and incense. Standing 24 cm, it wants a shelf with headroom or the middle of a table. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

Eight sports-ball charms, each with the ball's own surface cut into it - soccer pentagons, a golf ball's dimples, a basketball's seams - so they read as the real thing at charm size. Pick the one you want: every ball has a hole for a keyring or a chain, prints flat with no supports, and measures about 1.7" by 2". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A layered volleyball charm: the ball's panels are cut as separate raised layers, so the seams read as depth rather than a printed line. It is 1.6" by 1.4", has a hole at the top for a ring or a chain, and prints flat in one piece. Shown as a render, not a photo.

Design by CoisinhasdaManu

A little cauldron with a lid full of bubbles, sized to sit over a battery tea light: the light comes up through the bubbles and the whole thing glows. It prints in two parts, the cauldron and its top, so the top can be a different colour from the pot - the designer printed the tops in plain white and let the tea light do the colour. About 70 to 77 mm tall once the two parts are together. Battery tea light only, never a real flame. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DJH665

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

Twenty-six dog charms, each cut with a different dog in relief so it reads at a glance on a keyring or a necklace - the designer's three sets, in one listing. Pick the dog you want: every one has a hole at the top for the ring or the chain, prints flat with no supports, and measures about 1.4" by 2.4". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A pair of open heart outlines, each about 1.9" by 1.6" and barely over a gram, with a small hole at the top for the ear wire. They print flat, so the outline stays crisp and there is nothing to finish beyond fitting the hooks. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render, not a photo.

Design by C4UStudio

A vase with a wave running up its wall - a single spiralling surface, so the ridges catch the light differently as you walk past it. 180 mm tall, and shaped for dried flowers, pampas, feathers, or for nothing at all in a bare corner. It wants a dry arrangement rather than water. Print it in a silk or a matte filament and the waves do the rest of the work. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

Three round pet pendants struck like coins, each with a loop at the top for a chain or a keyring and each about 1.7" by 2". The set is all three, printed flat so the faces come out crisp. Shown as a render, not a photo.

Design by dominator334

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

One little ghost, three sizes of it: Small is 35 mm tall, Medium 45 mm and Large 64 mm, so a shelf can gather a few rather than carry a loner. Each prints as a rounded little spectre with a friendly face and no supports. Every ghost is its own object on the plate, so no multi-colour printer is needed - print them in different colours and they arrive as a set. The small one disappears into a bowl by the door; the large still fits in a hand. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A turtle small enough to sit on a shelf edge: the shell is modelled with its own scutes and the head, tail and legs are all there, so it reads as a real turtle rather than a toy one. 2.3" long and printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Type1Printing

A hinged box for rings and earrings, 150 by 83 by 20 mm closed: a tray with compartments, a lid that shuts on printed hinges, and two pins that press in to hold the hinge line - four printed parts, no screws, no supports. Small enough for a wash bag and rigid enough to keep its shape. A remix of "Parametric hinged small parts box" by Billiam on Printables, which is CC BY 4.0, and designed by Ivan Chamberlain under Creative Commons Attribution 4.0 (CC BY 4.0) - both are credited. Shown as a render of the printable model, not a photograph.

Design by Ivan Chamberlain

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A V-plow that clamps over the front of a clog: two mirrored blades, 118 mm long and 58 mm high, one for each shoe, that push snow aside as you walk. Shown as a render of the printable model, not a photograph.

Design by OVERTUREFilament

A bulldozer blade for a clog, with a toothed cutting edge and the brackets that hold it on: 81 mm across and 60 mm high, sold as a pair, one for each shoe. Shown as a render of the printable model, not a photograph.

Design by HazEyedeas

One pointed charm: an 18 mm cone on a flat base that presses into the hole of a clog, 13 mm across. Shown as a render of the printable model, not a photograph.

Design by ntalekt

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A large arched tunnel for a vivarium: a rock-textured hide that a reptile or amphibian can walk through and sleep in. 7.9" long, about 256 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by VivariumVisions

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

A crocodile in a straw hat and eyepatch, cut flat with four plugs behind it so it sits on top of a shoe: 33 x 29 mm. Shown as a render of the printable model, not a photograph.

Design by jstoner98

A soft-serve cone as a shoe charm: a 53 mm cone of waffle ridges under a swirl, with the plug behind it that pushes into a clog. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A fried egg 45 mm across, the yolk standing proud of a wavy white, plus the small plug that snaps behind it into a shoe. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A hockey stick lying across a puck, with the round plug that pushes it into a clog: 48 mm across, 13 mm from the shoe to the top of the stick, printed as the charm and its plug together. Shown as a render of the printable model, not a photograph.

Design by hudsonch79