The little tool for pulling the PTFE tube out of a Bambu A1 hot end without taking the printer apart - slot it behind the collar and lever. 1.7" long, printed in one piece in a minute or two. Remixed by R3DPanda from their own earlier version with a handle.
Design by R3DPanda
A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.
A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.
Design by Sitsero
A clip that holds a cable or a rope flat against a wall, in three sizes for different thicknesses. Each one is two parts that snap together - no supports, no screws - and the file prints all three sizes on one plate.
Design by GiskardReventlov
A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.
Design by PrintcessJacqueline3DDesigns
A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.
Design by inhabitworker
A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.
Design by Jerryie
A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.
Design by PanteraRuber
Winter forest deer ornaments: three deer among trees, cut as flat silhouettes with a hole to hang each one. 3.4" each, about 21 g of plastic for the set of three. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Walter3D
A ribbon Christmas tree with a bow: flat loops folded into a tree shape, with a hole at the top to hang it. 3.9" tall, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Ababskia3D
A Christmas teddy bear: a bear in a Santa hat with a ribbon to hang it by, printed in two sizes. 2" or 3.1" tall, about 12 g and 40 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by raven.log
A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Matthew
A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.
Design by tomo3D
A sleigh and a reindeer, printed twice each: the sleigh has a curled runner and a seat, the reindeer has antlers and a tail, and both are 5.5 mm deep so they hold shape from the side. The plate holds four earrings, a pair of sleighs and a pair of reindeer, and they mix on one ear each way. Shown as a render of the printable model, not a photograph.
Design by tomo3D
Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.
Design by instintkiller
Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.
Design by ThatGuy123568
A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.
Design by UncleFlappy
A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.
Design by ZHeights
A zip tie you can undo: printed in place with the pawl already free, so it locks, releases and locks again. 5.6" long, about 1.5 g, and it replaces the one-use ties on a cable bundle. Shown as a render, not a photo.
Design by 3DPrintHub
A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.
Design by Jerryie
Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.
Design by 3dprinting
A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.
Design by Terrain 6
Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.
Design by Chilly_275
A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.
Design by Asky
A Christmas tree built from organic, irregular tiers rather than a cone - the branches spiral and overhang, so it looks grown instead of drawn. Two sizes, 4" and 6" tall, each printed in one piece. Shown as a render, not a photo.
Design by 3dinsidegr
A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.
Design by fgiancarelli
A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.
Design by euro100xx
The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.
Design by kot1199
A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.
Design by jakub.fousek97
A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.
Design by mikan
A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.
Design by Clément Vasseneix
A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.
Design by Forged in Filament
A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.
Design by osamutake
A santa hat with the tip curling over: the brim is a raised band, the crown is domed and the tip hangs past the brim, so the shape reads from the side as well as the front. Each hat is 23.8 x 15.3 mm and 5.5 mm tall with a hole through the crown for a hook, and the plate prints six of them, which is three pairs. Shown as a render of the printable model, not a photograph.
Design by Ettore
A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.
Design by blunt
