$9.33Was $17.28
A low-poly vase built from big flat facets that twist as they rise, so light catches every plane differently. 5.5" across its widest and 3.9" tall, printed in one piece.
Design by Harry
$1.34Was $1.99
An articulated dragonfly: the body and each wing are cut into flat segments joined by print-in-place hinges, so it flexes in the hand and settles back flat when you set it down. It prints as one piece with no supports, 4" across by 2.7".
Design by Tybob24
$3.40Was $5.04
A cube of eight hinged blocks that folds in on itself: twist it one way and it turns inside out, fold it the other and it closes back into a cube, which is the whole trick and the reason one stays on a desk. It prints as a single piece with its hinges already in place, in two sizes, and needs no supports or assembly.
Design by Print3DFamily
$1.62Was $2.40
A crocodile printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles and curls in your hand. 4.0" long, printed in one piece.
Design by ThePrintDrawer
$7.09Was $10.50
A slug that ripples: the body is a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. About 3.0" curled, printed in one piece with no supports. Enlarged and remixed by yusuffles from matveymoo's "Curled up Friendly Slug", and sold under the same share-alike licence.
Design by yusuffles
$1.65Was $2.44
A lucky toad, printed in one piece with no supports, about 1.9" across and 2" tall with its little belly. Four come at the bulk rate.
Design by Ake Studio
$1.34Was $1.99
A plump bee that clips onto the top of a straw, wings raised and its stripes cut deep enough to read across a table. It suits the 10 mm Stanley straws, is 1.6" by 1.5", and prints in one piece with no supports.
Design by Morganja
$2.02Was $2.98
A monster printed as a chain of flexing segments - horns, a ridge of spines down its back and a tail that curls - so it stands up, slumps and wriggles. 3.9" tall, printed in one piece with no supports, in one colour or three.
Design by TinkerLink
$8.99Was $13.32
A bowl for rinsing rice: the water swirls through the grain and pours off the side while the rice stays put, so you stop losing half of it down the sink. Two sizes - 6.9" across and a smaller 4.8" - each printed in one piece, with the drain holes and the pouring lip part of the bowl.
Design by ValeraPerinski
$7.83Was $11.60
A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.
Design by Sitsero
$1.34Was $1.99
A tiny dragon printed as a chain of flexing segments, detailed all down its back and small enough to sit in two fingers. 3.0" long and only a few grams of plastic, printed in one piece.
Design by CrissyCat
$1.34Was $1.99
A lid that snaps onto a standard can and seals it up again between sips, and doubles as an opener when you slip it over the tab and tilt. It is the wider, support-free version, and it fits both the slim and the fat cans the designer built it around - European 202 cans, so if yours is a different can it is worth a quick measure. Light sanding on the slots is the only finishing it asks for.
Design by MakerShed
$3.72Was $6.88
An angled, ribbed plant pot for a windowsill, with a drip tray that stands it clear of its own water. The pot tapers up from a 45-degree base and drops into a tray with a hollow reservoir, so what drains out sits below the base instead of wicking back up into the soil, and the tray lifts off to empty. The floor has a 2.5 mm centre hole, a ring of six, and a ring of twelve at the outer edge. Forty-eight round bead ribs run up the angle and on to the rim, so the pot has something to grip and looks alive in daylight. Three sizes, each one as wide as it is tall: 2.5"x2.5", 3.25"x3.25" and 5"x5". It prints as two pieces, no supports and no assembly, in PLA - which is happy on an indoor sill, while a window that bakes in direct sun or a spot outside wants PETG. The last picture is a render of the printable model; the others are photographs of the printed pot.
$3.78Was $5.60
A dragon that prints in one piece with every plate of its body already jointed, so it coils and straightens straight off the bed - no supports, no assembly, and no loose parts. The spikes run the length of its back and read as armour when it is posed on a shelf. Three sizes: Small is 116 mm nose to tail, Medium is 140 mm and fits an A1 mini, and Large is 223 mm - the one that needs a full-size bed. The designer asks that anyone selling prints credit them and link the model page, which this listing does.
Design by CLUCKWORKS 3D
$1.34Was $2.26
A one-piece toy bow with a springy arrow that launches when you pull it back. Prints as a single piece with no assembly - ready to play with straight off the plate.
$15.39Was $28.50
A japandi vase with a rifted surface: a faceted body that catches the light along its ridges and narrows to the rim.
Design by DueMakers
$5.00Was $7.40
A snake printed in one piece with its body jointed along the whole of its length, so it coils and straightens as you play with it and holds whatever shape you leave it in. The scales run along its back and give it something to grip with. The designer prints it at 0.16 mm layers or finer at 100% scale, which is what keeps the joints free - print it coarser and it will come out stiff.
Design by Bash Studio 3D
$1.34Was $1.99
A dog's head that sits on top of a straw, ears up and nose forward.
Design by Morganja
$7.83Was $11.60
A star that opens and closes as you spin it: a print-in-place kinetic fidget with no assembly and no supports, so it comes off the plate ready to twist. Spinning it expands the arms from a closed cone into an open fan and back, which is the part that keeps hands busy, and it looks good parked on a desk either way. Best in a silk or colour-changing filament, which is what the designer recommends.
Design by Big-D-SyneS
$1.34Was $1.99
A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.
$1.44Was $2.66
A Jeep grille that rides on top of a straw, seven slots and all.
Design by Morganja
$1.34Was $1.99
A starfish printed as a chain of flexing segments, with five arms that trail and curl so it drapes over your hand. 4.5" across, printed in one piece with no supports.
Design by mieldeprot
$1.90Was $3.52
A baby dragon 3.9" long, printed in one piece. Two versions come off the plate: the flexi one is a chain of segments that curls and straightens in your hand, and the solid one is a single rigid body with the same shape. Pick which you want.
Design by Quantrex
$2.63Was $4.86
An articulated gecko 7.7" long, printed in one piece with every segment already moving - it curls over a shelf edge, drapes across a monitor and stays where you leave it. The plate also carries its little tongue.
Design by KrisCyber
$9.12Was $13.50
Four dinosaur cookie cutters with matching stamp inserts - press the stamp for the details, cut the outline, bake. Each cutter is about 3" across, and the set is four different animals.
Design by Merilno3D
$1.72Was $2.54
A clip-on egg separator: crack an egg into the channel and the white runs through while the yolk stays put. 3.6" long, printed in one piece, and it sits on the rim of a cup or a bowl.
Design by user_4069524941
$1.34Was $1.99
A 1:20 pallet, 50 by 55 mm, for an RC forklift or a shelf of scale freight. It prints with no supports and, at two walls with solid bottom layers, comes out solid through the body. The proportions follow a UK-style pallet rather than a North American one. Designed by CippyO and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by CippyO
$20.24Was $29.99
A 1/64 scale GP60B diesel for the Dragon Railway: the body, the bogies and the small fittings, printed across five plates, about 191 g of plastic in the set. It is a layout model rather than a toy that survives a floor, and RamBros publishes an assembly manual and a video covering the parts it wants. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by RamBros
$1.34Was $1.99
A bat whose wings are cut into linked segments, so they flex when it is handled and settle into a curve on a shelf - printed in one piece with every joint already free. 3.9" across the wingspan, about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Tybob24
$4.17Was $6.17
A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.
Design by DanyP86
$2.45Was $3.62
An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.
Design by IndigoRaptor
$13.88Was $20.56
A pair of little seated figures, each holding a round planter bowl - set them side by side on a windowsill with a succulent, a tea light or loose change in each cup. The two span 7.9" together and print from one file at about 103 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by cr_seb_olarte
$3.62Was $5.36
A small Japandi-style vase: a rounded bulb wrapped in fine vertical ribs, narrowing to a small open neck, so a single stem stands upright in it. 3.1" tall across a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by oakliz27
$5.64Was $8.36
A baby dragon that prints in one piece, with an articulated spine so the neck, wings and tail all bend and the whole thing can drape over a finger. It sits, curls and lies down, and needs no assembly and no supports. The picture is a render of the printable model, not a photograph of a finished print.
Design by Helios3D
$4.10Was $6.06
A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.
Design by pain.killer.2
$4.19Was $6.20
A giraffe lying down with its neck folded back and its legs tucked - printed as a chain of segments, so it flops about when you pick it up. 6.5" long, and the eyes print as separate 8 mm pieces that go in after. Shown as a render, not a photo.
Design by SHF3D.
$11.98Was $17.74
A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.
Design by Asky
$6.02Was $8.92
A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.
Design by Nix3D
$9.28Was $13.74
Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.
Design by Merilno3D
$2.78Was $4.12
A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.
Design by Jirka108
$4.70Was $7.46
Four Halloween cutters - pumpkin, ghost, bat and the like - about 3" across each, printed with a cutting rim deep enough for biscuit dough or Play-Doh. One plate prints the set. Shown as a render, not a photo.
Design by Creaitivity Studio
$20.24Was $29.99
An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.
Design by lunatiic
$16.20Was $24.00
A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.
Design by Alex
$20.24Was $29.99
A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.
Design by MicahW3D
$7.99Was $11.84
A mosquito trap that uses a jar you already have: a funnel that drops into a mason jar's mouth, so a jar of water and a spoon of sugar becomes a trap. The cone lets a mosquito in and the jar's own walls keep it there. Three funnels come off the plate, 76 mm across and 47 mm tall, for the jar sizes the designer covered - standard jam jars among them. Designed by IanFoulds, a remix of the Mosquito Trap by Urasxman, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by IanFoulds
$20.24Was $29.99
A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.
Design by specialman
$13.36Was $19.78
A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.
Design by NordicCreativa
$1.53Was $2.26
A paw that rides on top of a straw: the straw passes through the middle of it, the paw sits above the lid, and the raised pad and four toes catch the light as the cup moves. It is made for the 10 mm Stanley straws, 3.5" tall by 1.6" across, and it prints in one piece. Shown as a render, not a photo.
Design by Morganja
