3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A sleigh and a reindeer, printed twice each: the sleigh has a curled runner and a seat, the reindeer has antlers and a tail, and both are 5.5 mm deep so they hold shape from the side. The plate holds four earrings, a pair of sleighs and a pair of reindeer, and they mix on one ear each way. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A santa hat with the tip curling over: the brim is a raised band, the crown is domed and the tip hangs past the brim, so the shape reads from the side as well as the front. Each hat is 23.8 x 15.3 mm and 5.5 mm tall with a hole through the crown for a hook, and the plate prints six of them, which is three pairs. Shown as a render of the printable model, not a photograph.

Design by Ettore

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

A flat-pack stand for holding earrings: a base plate, two uprights and a crossbar that slot into each other, with the uprights stepped so pairs hang at different heights instead of bunching. Assembled it is about 170 x 100 mm and stands 13 mm deep, big enough for a shelf or a dresser top. It prints as four flat pieces with no supports and comes to about 83 g of plastic. Shown as a render of the printable model, not a photograph.

Design by Recflying

A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.

Design by thift88

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A mushroom charm in three pieces that press together: a domed cap, the gills under it and a stem with fixing pegs. Printing it in parts lets the cap take one colour and the stem another, and the assembled charm is about 23 mm tall and 13 mm across with a hole in the cap for a hook. Shown as a render of the printable model, not a photograph.

Design by iNkosi3D

A butterfly drawn as one continuous line and cut 1.5 mm thick at 150 x 160 mm, so it sits on a wall as a shape that casts a shadow rather than a solid plaque. It prints flat in one piece with no supports and needs no fixings: mounting putty or a pin behind the body is enough. Shown as a render of the printable model, not a photograph.

Design by PediM

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

An autumn sign for a windowsill or a shelf: the word Hello stacked over Fall with a pumpkin alongside, flat on the back so it sits against a wall, and printed as separate pieces so the lettering and the pumpkin each take their own filament - the designer printed his in matte white, orange and brown. Designed by JMOS and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by JMOS

Christmas ornaments in the shape of balls, in three sizes - 40, 60 and 80 mm across - with the number of double ribs going up with the size: six on the smallest, ten in the middle and fourteen on the largest, each rib 3 mm wide. Each ball prints in two pieces, the ball and the bottom that closes it, and the designer prints that bottom with a support so the curve comes out clean and the ball sits tight against it. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A spiral vase that stands on its own round base. Lloyd Tapper started from Tru!e's spiral flower pot and then fixed the thing that annoyed him - the vase slid around on the base - by adding a notch under the vase and turning the elevators on the base into cones, so the two move together when you pick the vase up. Both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Lloyd Tapper

A snowflake cut to sit over the top corner of a door frame, so the corner of a door is dressed for the season. It prints flat and reads well in one colour or in several - the designer's own photos show both. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

An ornament that hooks over the corner of a door frame: a bauble hanging from a bow on the trim above a door, flat on the back so it sits square in the corner. Sold as one corner piece, 196 by 207 mm. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A vase 178 mm tall, its wall twisted into a spiral that narrows as it rises, so the shadow on it moves as you walk past. The designer also publishes a fuzzy-skin version for a soft matte surface and a 40 per cent larger one; this is the original size, printed smooth. Designed by DueMakers and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by DueMakers

Three stick figures in fighting poses, each one holding your pencil where it would hold a weapon: an archer drawing a pencil like a bow, a spearman resting on a long one, and a sniper kneeling with one as a rifle. The archer takes short pencils of about 8 to 9 cm, the other two take ordinary 10 to 16 cm ones. Sold as the set of three. Designed by Gekko and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Gekko

A Santa in his sleigh for the corner of a door frame: the sleigh runs behind him as a counterweight, so the piece sits up on its own along the top corner of a door or a window. The designer's updated file carries both the left-hand and the right-hand version, so the pair is what is printed. Designed by lindnjoe and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.

Design by TinkerTogether

A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.

Design by MakerShed

A fidget spinner small enough to live in a pocket: one piece, no bearings, no axle to glue, printed in place so the two halves and their weights come off the plate ready to spin. It is a 15-minute print in the designer's own profile, which is why it makes a good giveaway or market-stock item. Printed in a silk filament the spinning face catches the light. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DragonFusion3D

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.

Design by UncleFlappy

A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.

Design by ArmadilloFDM

A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.

Design by user_3738174853

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.

Design by Merilno3D

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

A pen holder clad in raised dragon scales, hexagonal all the way round, with a smooth inner cup for pens, pencils or brushes. 3.1" across and 4" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3DWoosh

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Weso2976

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc