3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Two five-pointed stars, 35 mm across and 2 mm thick, a hole at the tip of one point for a hook. Printed flat in PLA with no supports, and light enough that the pair is about a gram and a half of plastic. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

A tulip built from flat overlapping layers - a rounded bloom sitting over its leaves - as a pair of earrings 21 mm tall and 2.4 mm thick, with a hole through the back for a hook. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Ettore

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A hinged box for rings and earrings, 150 by 83 by 20 mm closed: a tray with compartments, a lid that shuts on printed hinges, and two pins that press in to hold the hinge line - four printed parts, no screws, no supports. Small enough for a wash bag and rigid enough to keep its shape. A remix of "Parametric hinged small parts box" by Billiam on Printables, which is CC BY 4.0, and designed by Ivan Chamberlain under Creative Commons Attribution 4.0 (CC BY 4.0) - both are credited. Shown as a render of the printable model, not a photograph.

Design by Ivan Chamberlain

The classic folded awareness ribbon with a keyring loop at the top, printed flat so the fold reads cleanly on both faces. It is 2.5" long by 1.4" wide and prints in whatever colour you choose. Shown as a render, not a photo.

Design by Miss3DP

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

Twenty-six dog charms, each cut with a different dog in relief so it reads at a glance on a keyring or a necklace - the designer's three sets, in one listing. Pick the dog you want: every one has a hole at the top for the ring or the chain, prints flat with no supports, and measures about 1.4" by 2.4". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A turtle small enough to sit on a shelf edge: the shell is modelled with its own scutes and the head, tail and legs are all there, so it reads as a real turtle rather than a toy one. 2.3" long and printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Type1Printing

Three round pet pendants struck like coins, each with a loop at the top for a chain or a keyring and each about 1.7" by 2". The set is all three, printed flat so the faces come out crisp. Shown as a render, not a photo.

Design by dominator334

A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.

Design by UncleFlappy

Four Jeep charms, each a different model cut in relief and each with a hole at the top for a keyring or a chain. Pick the one you want - they print flat with no supports and measure about 2.4" by 2.4". Shown as a render, not a photo.

Design by dominator334

Mark the shark as a keychain or as a necklace charm - the same shark in two fittings, one with a ring hole and one sized for a chain. It prints flat with no supports, about 2.4" long. Shown as a render, not a photo.

Design by dominator334

A pair of open heart outlines, each about 1.9" by 1.6" and barely over a gram, with a small hole at the top for the ear wire. They print flat, so the outline stays crisp and there is nothing to finish beyond fitting the hooks. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render, not a photo.

Design by C4UStudio

A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.

Design by ZHeights

A layered volleyball charm: the ball's panels are cut as separate raised layers, so the seams read as depth rather than a printed line. It is 1.6" by 1.4", has a hole at the top for a ring or a chain, and prints flat in one piece. Shown as a render, not a photo.

Design by CoisinhasdaManu

A dragon egg with scales cut over the whole shell and a lid that lifts off, so it hides something small. Three sizes: 1.4", 2.8" and 3.7" tall, the big one weighing about 50 g. Printed in one piece, lid and all. Shown as a render, not a photo.

Design by Type1Printing

Eight sports-ball charms, each with the ball's own surface cut into it - soccer pentagons, a golf ball's dimples, a basketball's seams - so they read as the real thing at charm size. Pick the one you want: every ball has a hole for a keyring or a chain, prints flat with no supports, and measures about 1.7" by 2". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A 2 mm PLA cake stencil, 6 x 4 inches, with Happy Birthday and three balloons cut right through. The lettering is a stencil face, so the middles of the a, p, B, R and D stay attached to the plaque instead of falling out. Lay it on a sheet of parchment over the cake, dust with cocoa or icing sugar, and lift it away. Four or more come at the bulk rate. The picture is a render of the printable model, not a photograph; real photos go up once the first one is printed.

A sitting baby elephant with its trunk curled up and its ears out, printed in one piece with no supports. 2.4" tall, and about 9 g of plastic, so it sits on a shelf or a desk without a base. Shown as a render, not a photo.

Design by user_1541493983

Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.

Design by Merilno3D

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

A vase 178 mm tall, its wall twisted into a spiral that narrows as it rises, so the shadow on it moves as you walk past. The designer also publishes a fuzzy-skin version for a soft matte surface and a 40 per cent larger one; this is the original size, printed smooth. Designed by DueMakers and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by DueMakers

A spiral vase that stands on its own round base. Lloyd Tapper started from Tru!e's spiral flower pot and then fixed the thing that annoyed him - the vase slid around on the base - by adding a notch under the vase and turning the elevators on the base into cones, so the two move together when you pick the vase up. Both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Lloyd Tapper

An Easter egg in two halves that spiral into each other: you twist one into the other and the spiral holds, so the egg is a toy as much as an ornament, and it comes apart again. Sold as the two-part egg. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

Two horses facing each other, their necks curved so the space between them is a heart - a silhouette cut from 5 mm and 180 mm across. Printed flat in one piece, so it leans on a shelf or a mantel rather than hanging. Designed by MazziNiX and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by MazziNiX

An autumn sign for a windowsill or a shelf: the word Hello stacked over Fall with a pumpkin alongside, flat on the back so it sits against a wall, and printed as separate pieces so the lettering and the pumpkin each take their own filament - the designer printed his in matte white, orange and brown. Designed by JMOS and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by JMOS

An egg with a door in it: the front opens and shuts on a hinge printed in place, so the little house egg can be opened as often as you like - the designer notes the first opening needs a gentle pull to snap the hinge free. Printed in the flat-bottomed version the designer supplies, so it stands. Designed by AcmeArt and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by AcmeArt

Cats in silhouette for the wall: four printed pieces - three frames, each with a cat, and one butterfly that hangs between them - every shape cut from 5 mm, so they hang as a set and can be arranged the way your wall wants them. The designer prints them in matte black or another strong plain colour, because the outline is the whole picture. Sold as the set. Designed by carlos_peral and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by carlos_peral

A vase drawn for spiral vase mode: one continuous wall spiralling up from the foot to the lip, so it prints in a single unbroken pass with no seam, and a light behind it shows the twist. Designed by elio196721 and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by elio196721

A heart standing on a base with wedding rings resting against the top - the designer sets them into the part that touches the heart and suggests turning on ironing, or moving them to whichever face you prefer. A small piece for an anniversary shelf or a wedding table. Designed by bambaxp and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by bambaxp

A bunny built from flat planes: the low-poly faceting catches the light on every angle, and at 40 mm tall it is a small figure for a shelf, a windowsill or an Easter table. Printed in one piece. Designed by Pejdro and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by Pejdro

A rose and its stem printed as one piece, so there is no assembly at the end: the petals spiral out of the bud and the stem runs down to a base that stands on a desk. The designer prints it as a classic print rather than vase mode, and suggests one perimeter and no infill with a transparent filament if you want the light to come through the petals. The page credits Lytta and RubixDragon for the roses it was built from - all three designers are named on this page. Printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by user_531694306

Happy Birthday for a cyclist: a bicycle and rider over the words, cut flat and standing in the cake. 7" wide, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

A fish for the wall, cut flat: a simple fishing silhouette that the designer reshaped slightly to make it print cleanly. At 238 by 166 mm it is big enough to hold a wall on its own - a shed, a cabin, or the wall of somebody who would rather be fishing. Designed by MazziNiX and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by MazziNiX

A football cake topper - a player, a ball and the words Happy Birthday - printed flat as one piece that stands in the cake. 5.5" wide, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Regata

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A Happy Birthday stencil for cakes and cookies: the words cut through a thin plate, so icing, cocoa or dusting sugar goes on through it. 3.9" wide, about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A bow tie printed as an open voronoi lattice, light enough to wear and unlike any fabric one - the knot is part of the same one-piece print. 4.5" across. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by alexlluch

A tree-shaped photo frame: a heart in the middle and branches around it holding small photographs, with the plates that back them printed alongside so the pictures stay in without glue or tape. The designer scaled the pieces so the larger tree prints on one sheet, and suggests an acetate sheet in front of each photo to keep the dust off. Sold as the printed set. Designed by PediMR and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by PediMR

Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Astler

A dragon egg with overlapping scales and a lid that lifts off, so it hides something small inside. 2.4" tall, printed in one piece - the shell and the lid come off the plate together. Shown as a render, not a photo.

Design by LLucas404

A block-letter Happy Birthday banner: chunky script letters standing on a base strip with a candle and balloon tucked in among them, printed flat as one piece. 6.3" wide, about 27 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by bigdobbo3D

A thin calligraphic Happy Birthday topper, the loops and swashes joined into one delicate piece that lies across a cake. 5.4" at its widest and under 4 mm thick, about 15 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ana Bonacho