3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.

Design by AmandaRoos

Three holders that keep bottles lying down in the fridge instead of rolling out of the door - each cradles one bottle on its side and stacks with the others. The plate prints three, and each is about 9.4" long. Shown as a render, not a photo.

Design by RossMacAllan

A zip tie you can undo: printed in place with the pawl already free, so it locks, releases and locks again. 5.6" long, about 1.5 g, and it replaces the one-use ties on a cable bundle. Shown as a render, not a photo.

Design by 3DPrintHub

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A sitting baby elephant with its trunk curled up and its ears out, printed in one piece with no supports. 2.4" tall, and about 9 g of plastic, so it sits on a shelf or a desk without a base. Shown as a render, not a photo.

Design by user_1541493983

Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.

Design by Merilno3D

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

A vase 178 mm tall, its wall twisted into a spiral that narrows as it rises, so the shadow on it moves as you walk past. The designer also publishes a fuzzy-skin version for a soft matte surface and a 40 per cent larger one; this is the original size, printed smooth. Designed by DueMakers and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by DueMakers

A rose for the top of a 40 oz Stanley cup lid: the bloom prints standing up on the topper, so a plain cup gets a flower on it with nothing to glue in place. It fits the 40 oz lid. Designed by speedster, who remixed Picture_it's blank Stanley lid topper - both makers are credited on this page and both licences are recorded beside the file. Printed under Creative Commons Attribution 4.0 (CC BY 4.0); the topper it is built on is CC BY-SA 4.0, and the print is sold unaltered. Shown as a render of the printable model, not a photograph.

Design by speedster

A spiral vase that stands on its own round base. Lloyd Tapper started from Tru!e's spiral flower pot and then fixed the thing that annoyed him - the vase slid around on the base - by adding a notch under the vase and turning the elevators on the base into cones, so the two move together when you pick the vase up. Both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Lloyd Tapper

A blank topper that sits on a 40 oz Stanley cup lid, flat and smooth, so it is a base for whatever goes on top: the designer's own page explains how to add text to it in Bambu Studio, choosing the font and the size and then the colour of the topper and of the writing separately. Sold blank, exactly as published. Designed by Picture_it and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Picture_it

An autumn sign for a windowsill or a shelf: the word Hello stacked over Fall with a pumpkin alongside, flat on the back so it sits against a wall, and printed as separate pieces so the lettering and the pumpkin each take their own filament - the designer printed his in matte white, orange and brown. Designed by JMOS and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by JMOS

Cats in silhouette for the wall: four printed pieces - three frames, each with a cat, and one butterfly that hangs between them - every shape cut from 5 mm, so they hang as a set and can be arranged the way your wall wants them. The designer prints them in matte black or another strong plain colour, because the outline is the whole picture. Sold as the set. Designed by carlos_peral and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by carlos_peral

A vase drawn for spiral vase mode: one continuous wall spiralling up from the foot to the lip, so it prints in a single unbroken pass with no seam, and a light behind it shows the twist. Designed by elio196721 and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by elio196721

A rose and its stem printed as one piece, so there is no assembly at the end: the petals spiral out of the bud and the stem runs down to a base that stands on a desk. The designer prints it as a classic print rather than vase mode, and suggests one perimeter and no infill with a transparent filament if you want the light to come through the petals. The page credits Lytta and RubixDragon for the roses it was built from - all three designers are named on this page. Printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by user_531694306

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A tree-shaped photo frame: a heart in the middle and branches around it holding small photographs, with the plates that back them printed alongside so the pictures stay in without glue or tape. The designer scaled the pieces so the larger tree prints on one sheet, and suggests an acetate sheet in front of each photo to keep the dust off. Sold as the printed set. Designed by PediMR and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by PediMR

Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Astler

A dragon egg with overlapping scales and a lid that lifts off, so it hides something small inside. 2.4" tall, printed in one piece - the shell and the lid come off the plate together. Shown as a render, not a photo.

Design by LLucas404

An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by bigdobbo3D

A candy machine that turns a canning jar into a dispenser: a base that screws onto the jar's own lid ring, a knob and a printed pin, so no screw is needed anywhere. Fill the jar with sweets, fit the base, turn the knob and a few drop through. The designer also ships a stronger pin for silk PLA, and a second file for the narrower Hema store jar. Designed by carlbelcher and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by carlbelcher

A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SuperBgr

A flower on a stem that stands on its own - the petals print as one piece with the stalk, so it needs no water and no vase. 3.9" tall, and the stem is a separate file if you want a different height. Shown as a render, not a photo.

Design by JarJar

A BMW E36 mid-drift, cut as a minimalist silhouette with the car sitting low and sideways. 7" x 5.4", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Kuba

An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Michel

A stag head in faceted planes, printed as one flat piece - a low-poly wall hanging in a single colour. 5.7" x 6.2", about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A wolf in profile built from flat geometric planes: one piece, printed flat, for a wall or a desk stand. 7" x 4.3", about 5 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A large arched tunnel for a vivarium: a rock-textured hide that a reptile or amphibian can walk through and sleep in. 7.9" long, about 256 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by VivariumVisions

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.

Design by thift88

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.