A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.
Design by PanteraRuber
A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Matthew
A screw-top capsule for the small things that have to stay dry: matches, pills, a spare battery, a couple of picks. A loop on the cap hangs it from a backpack or a bike frame. Six sizes, 48 mm at the smallest and 128 mm at the largest, each printing as a container and its cap with no supports. The designer's optional TPU gasket - the part that makes it properly waterproof - is not something the shop prints, so as printed the thread keeps splashes and pocket lint out rather than a soaking. Designed by squinn and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by squinn
A can cap that opens the can as well: press it over the top of a standard 355 ml tab can and the drink is covered between sips, with the opener moulded into the same part. It prints in one piece in about forty minutes with no supports. Designed by BUD THE RETIRED PRINT GUY and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.
Design by BUD THE RETIRED PRINT GUY
A lid that presses onto an open drinks can and slides shut, keeping dust, wasps and debris out of a beer or a soda between sips. Two fits are on offer: the standard can, whose lid measures 1.4 by 1.9 inches, and a wider one at 1.5 by 2.4 inches for a fatter 16 oz rim. Each prints as a lid and its sliding cover, and the standard lid also comes in the designer's looser-fitting version for a can that runs tight. Designed by Tiger prints, who remixed EcoDad's Printables lid - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by Tiger prints
An arrow holder that takes up to twelve arrows, for shafts up to 11/32 of an inch across. One arrow or a dozen loaded on the same side, it stays upright, and it needs no supports; the designer printed his on an A1 mini. It is not a frugal print - the designer says so himself - so it is priced by what it weighs rather than by the pose. Designed by StickMan and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by StickMan
A pinecone geocache: a hollow cone with a screw-on cap and a loop at the top for a string or a length of wire, so it can hang in a branch. It prints in two pieces and neither needs supports. For a cache that lives outdoors, PETG keeps its shape in a hot car or a sunny hedge better than PLA. Designed by Soalar, who remixed it from Izak02's Pine cone cache - both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Soalar
Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.
Design by ThatGuy123568
A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.
Design by dhs
A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by LilÕJimbob
A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.
Design by blunt
