3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.

A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.

Design by Sitsero

A teepee that holds the spare rolls: two printed panels hinged into a tent, a base that keeps it square and three dowels that peg it together, with a roll inside. 6" across and 5.3" tall, printed in panels and assembled - the modular system, in the size that fits a small printer. Shown as a render, not a photo.

Design by ThePhilosopher

A strip that threads onto a guitar strap and holds a stack of picks, so a fresh one is within reach in the middle of a song: 100 mm long and 25 mm wide, printed in one piece. It sits on the strap rather than in a pocket, which is where picks go to be lost. Designed by willywidget and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by willywidget

An LP on the wall: a back plate with a shelf the cover stands on and two brackets that hold the record upright in front of it, so the sleeve and the disc are both on show. 218 by 214 mm and 187 mm deep, printed as one piece. Designed by LucMonnom and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by LucMonnom

A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.

Design by UncleFlappy

A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by gareth7562

Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by SF3DPrints

A practice mute for trombone, printed in three parts: the long tapered body that goes down into the bell, the flared cup that caps it, and the small collar that keeps the two together. 250 mm long and 193 mm across the cup, so it takes a full-size bell. The cup is what does the muting, so the horn can be played in an apartment without the neighbours learning the set list. Designed by 烤肉大师 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by 烤肉大师

A capo in two printed parts: a jaw that sits across the strings and the lever that clamps it down, 92 mm wide so it spans a standard six-string fretboard. It goes on the neck above the fret and holds the strings at the new position, which is what lets one shape be played in any key. Designed by Kevdev, a remix of the Guitar Capo by HarleyPrints, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Kevdev

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A plectrum printed flat at half a millimetre, 27 mm tall and 24 mm across, with the designer's design across the face - the pun in the name is the whole idea. Thin picks bend more than thick ones, so this is the one for strumming rather than for shredding. Designed by marshal.meacham and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by marshal.meacham

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament