3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A race medal with a moulded ribbon and a numbered disc in the middle. The file holds first, second and third, so a set covers a whole podium for a school race or a party game. The picture is a render of the printable model, not a photograph of a finished print.

Design by Rodrigo Ferriz

The same heart twice, one a little larger than the other, each cut out of a single outline with its own hang hole - so one wears on a hook and the other takes a keyring. Both print flat together, about 28 x 29 mm and 2.4 mm thick. Shown as a render of the printable model, not a photograph.

Design by Brightbox

Two flip flops printed as one piece, each with a raised strap and a toe post standing up through the sole, so they read as sandals rather than flat outlines. Each is about 30 mm long with a hole at the heel for a hook, and the pair comes off the plate together. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A hummingbird in flight framed by a teardrop outline: the bird sits inside the frame and joins it at the wing, with the hook tab above. Each is 27 x 41 mm and 2.3 mm thick, so the frame holds its shape rather than sagging, and the pair prints mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A heart built from two nested outlines, so it reads as a heart from across a room and stays light on the ear. Each is 33 x 32.4 mm and 4.1 mm thick at the join, with a hole at the top for a hook, and the plate prints four hearts, which is two pairs. Shown as a render of the printable model, not a photograph.

Design by Fetter79

A molar with a smiling face cut into it, in two sizes: 30 x 23 mm and 25 x 18 mm, with a hole at the crown for a hook. A gift for a dentist, a hygienist, or anyone who likes a tooth with a face on it. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by HaPeHu

A paw print with four toe pads and a deep heel pad, cut 2.3 mm thick so the pads stay proud of the outline instead of blurring into it. Each paw is 23 x 24.5 mm with a hole between the toes for a hook, and the pair is mirrored so the prints face the same way when they are worn. Shown as a render of the printable model, not a photograph.

Design by Slowpoke’s Workshop

A mirrored flourish - a curling stem with leaf-shaped tips - cut 2 mm thick, each about 24 x 36 mm with a hole at the end of the stem for a hook. The pair prints flat as one piece and lies along the ear rather than hanging off it. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A flip-flop outline, 48 x 18 mm and 2 mm thick, with the strap drawn as an open line across the sole and an eyelet at the toe for a hook. Long and narrow, so the pair swings rather than sitting flat against the ear. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A hot air balloon with its gores moulded in, the netting raised and a basket hanging under it on two lines, printed 1.9 mm thick. Each is 30 x 50 mm with a hole at the top of the envelope for a hook, and the pair prints together. Shown as a render of the printable model, not a photograph.

Design by ProtoEngineering

One continuous line draws a face in profile, cut out flat as an earring: 26 mm tall, 2 mm thick, with a hole at the top for a hook. Sold as a pair, mirrored so the two faces look at each other. Shown as a render of the printable model, not a photograph.

Design by Margen3d

A lotus flower built from three rings of petals, the outer ones splayed and the inner ones cupped, so the flower has depth from every angle. Each is 42 x 41 mm and 2 mm thick with a hole worked into the top petal for a hook, and the pair prints side by side on one plate. Shown as a render of the printable model, not a photograph.

Design by Pistachio

A filigree arch: a curved band of scrollwork with the spaces cut right through, so it reads as lace from the front and sits like a crescent against the ear. Each is 26 x 34 mm and 2.3 mm thick with the hook tab at the top, and the pair is mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

Six hearts on one plate: a large pair at 31 x 28 mm and two smaller pairs at 12 x 11 mm and 10 x 9 mm, each with a smiling face and a hole for a hook. Sold as a set of three pairs - the large hearts for everyday, the two small pairs for a second piercing or to give away. Shown as a render of the printable model, not a photograph.

Design by Merche

A pair of sunglasses with the arms and a bridge moulded in, printed 2.5 mm thick and 32 mm across, with a hole in each arm for a hook. They are a joke that prints properly: the lenses are open, so the shape holds at this size and reads at a glance. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A dolphin inside an oval ring, 42 x 37 mm and 2.6 mm thick, with a small eyelet at the top for a hook. The dolphin is cut clear of the ring behind it, so the two shapes read separately and the pair hangs as two clean outlines. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Ghost1975w

A six-fold filigree snowflake, 35 x 31 mm and 1.5 mm thick, with a hole at the top for a hook. Every branch is openwork, so it prints as fine line after fine line rather than a solid plate, and it catches the light as it moves. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by PediMR

XO in solid letters, 40 x 37 mm and 2 mm thick, with a small hole at the base of the O for a hook. The two letters are cut as one piece, so each earring hangs as a single word rather than two separate charms. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by SynneLuna

A cowboy boot with the shaft, pull tabs, heel and stitched sole all standing proud of the outline, so it reads as a boot rather than a silhouette. Each is 31 mm square and 2 mm thick with a hole in the shaft for a hook, and the pair prints mirrored. Shown as a render of the printable model, not a photograph.

Design by D.MacMcAlister

A heart drawn in a few asymmetric arcs, 34 x 29 mm and 2.3 mm thick, with a hole at the top for a hook. The plate is a solid rim around a cut-out centre, so it reads as a sketch of a heart rather than a filled one, and the pair hangs light. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A heart outline with a horse's head drawn inside it in one open cut, 40 x 37 mm and 2 mm thick, with a hole at the top of the heart for a hook. Almost all of it is outline, so it is light on the ear and reads as a horse from across a room rather than only up close. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

Two five-pointed stars, 35 mm across and 2 mm thick, a hole at the tip of one point for a hook. Printed flat in PLA with no supports, and light enough that the pair is about a gram and a half of plastic. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

A tulip built from flat overlapping layers - a rounded bloom sitting over its leaves - as a pair of earrings 21 mm tall and 2.4 mm thick, with a hole through the back for a hook. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Ettore

The classic folded awareness ribbon with a keyring loop at the top, printed flat so the fold reads cleanly on both faces. It is 2.5" long by 1.4" wide and prints in whatever colour you choose. Shown as a render, not a photo.

Design by Miss3DP

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

Twenty-six dog charms, each cut with a different dog in relief so it reads at a glance on a keyring or a necklace - the designer's three sets, in one listing. Pick the dog you want: every one has a hole at the top for the ring or the chain, prints flat with no supports, and measures about 1.4" by 2.4". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

Three round pet pendants struck like coins, each with a loop at the top for a chain or a keyring and each about 1.7" by 2". The set is all three, printed flat so the faces come out crisp. Shown as a render, not a photo.

Design by dominator334

Four Jeep charms, each a different model cut in relief and each with a hole at the top for a keyring or a chain. Pick the one you want - they print flat with no supports and measure about 2.4" by 2.4". Shown as a render, not a photo.

Design by dominator334

Mark the shark as a keychain or as a necklace charm - the same shark in two fittings, one with a ring hole and one sized for a chain. It prints flat with no supports, about 2.4" long. Shown as a render, not a photo.

Design by dominator334

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose

A layered volleyball charm: the ball's panels are cut as separate raised layers, so the seams read as depth rather than a printed line. It is 1.6" by 1.4", has a hole at the top for a ring or a chain, and prints flat in one piece. Shown as a render, not a photo.

Design by CoisinhasdaManu

Eight sports-ball charms, each with the ball's own surface cut into it - soccer pentagons, a golf ball's dimples, a basketball's seams - so they read as the real thing at charm size. Pick the one you want: every ball has a hole for a keyring or a chain, prints flat with no supports, and measures about 1.7" by 2". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.

Design by AmandaRoos

An Easter egg in two halves that spiral into each other: you twist one into the other and the spiral holds, so the egg is a toy as much as an ornament, and it comes apart again. Sold as the two-part egg. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

An egg with a door in it: the front opens and shuts on a hinge printed in place, so the little house egg can be opened as often as you like - the designer notes the first opening needs a gentle pull to snap the hinge free. Printed in the flat-bottomed version the designer supplies, so it stands. Designed by AcmeArt and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by AcmeArt

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

A pair of eighth notes, each an outline rather than a filled shape, so they stay light on the ear and catch the light along the stem. Each is 20 x 22.7 mm and 2 mm thick, with the hole in the note head for a hook, and they print mirrored so the two notes sit opposite each other. Shown as a render of the printable model, not a photograph.

Design by mikesak29

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A watermelon slice with the rind standing proud of the flesh and the seeds cut into it, 26.7 x 25.9 mm and 1.6 mm thick with a hole at the top for a hook. The plate prints eight slices, which is four pairs; order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A bee with a rounded body, two wings standing off it and a hook hole at the head, printed as one piece at 25 x 29 mm. The body is domed rather than flat, so it reads as a bee from the side too, and it is light enough to wear all day. Order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by wally

A butterfly with its wings open and the veins left raised, so the pattern survives printing instead of filling in. Each is 49 x 31 mm and 1.6 mm thick, thin enough to sit flat against the ear, with a hole at the top for a hook. The pair prints as two mirrored butterflies. Shown as a render of the printable model, not a photograph.

Design by FrazierSmith

Four feather shapes, each printed twice so every design makes a mirrored pair: 60 mm long, 2 mm thick, with the barbs cut through so the feather is an outline and the quill shows. Printed flat with no supports. The plate holds all eight earrings - the whole set of four pairs - and they come in one colour. Shown as a render of the printable model, not a photograph.

Design by KameleonForge

One pointed charm: an 18 mm cone on a flat base that presses into the hole of a clog, 13 mm across. Shown as a render of the printable model, not a photograph.

Design by ntalekt

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A bulldozer blade for a clog, with a toothed cutting edge and the brackets that hold it on: 81 mm across and 60 mm high, sold as a pair, one for each shoe. Shown as a render of the printable model, not a photograph.

Design by HazEyedeas