A lid that snaps onto a standard can and seals it up again between sips, and doubles as an opener when you slip it over the tab and tilt. It is the wider, support-free version, and it fits both the slim and the fat cans the designer built it around - European 202 cans, so if yours is a different can it is worth a quick measure. Light sanding on the slots is the only finishing it asks for.
Design by MakerShed
A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.
A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.
Design by Sitsero
Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.
A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.
Design by Morganja
A Jeep grille that rides on top of a straw, seven slots and all. Shown as a render, not a photo.
Design by Morganja
A dog's head that sits on top of a straw, ears up and nose forward. Shown as a render, not a photo.
Design by Morganja
A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.
Design by JEP0405
A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.
Design by Morganja
A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.
Design by Morganja
A strip that threads onto a guitar strap and holds a stack of picks, so a fresh one is within reach in the middle of a song: 100 mm long and 25 mm wide, printed in one piece. It sits on the strap rather than in a pocket, which is where picks go to be lost. Designed by willywidget and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by willywidget
An LP on the wall: a back plate with a shelf the cover stands on and two brackets that hold the record upright in front of it, so the sleeve and the disc are both on show. 218 by 214 mm and 187 mm deep, printed as one piece. Designed by LucMonnom and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.
Design by LucMonnom
A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.
Design by jakub.fousek97
A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.
A paw that rides on top of a straw: the straw passes through the middle of it, the paw sits above the lid, and the raised pad and four toes catch the light as the cup moves. It is made for the 10 mm Stanley straws, 3.5" tall by 1.6" across, and it prints in one piece. Shown as a render, not a photo.
Design by Morganja
A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.
Design by iNkosi3D
A T-rex that holds your page: the dinosaur stands on the spine of the book with its legs either side, and the tail curls over the top. It prints flat in one piece, 3.6" tall. Shown as a render, not a photo.
Design by UncleFlappy
A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.
Design by Tim
A plump bee that clips onto the top of a straw, wings raised and its stripes cut deep enough to read across a table. It suits the 10 mm Stanley straws, is 1.6" by 1.5", and prints in one piece with no supports. Shown as a render, not a photo.
Design by Morganja
A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.
Design by AmandaRoos
A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.
Design by MeltedMoose
A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by gareth7562
Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by SF3DPrints
A practice mute for trombone, printed in three parts: the long tapered body that goes down into the bell, the flared cup that caps it, and the small collar that keeps the two together. 250 mm long and 193 mm across the cup, so it takes a full-size bell. The cup is what does the muting, so the horn can be played in an apartment without the neighbours learning the set list. Designed by 烤肉大师 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by 烤肉大师
A capo in two printed parts: a jaw that sits across the strings and the lever that clamps it down, 92 mm wide so it spans a standard six-string fretboard. It goes on the neck above the fret and holds the strings at the new position, which is what lets one shape be played in any key. Designed by Kevdev, a remix of the Guitar Capo by HarleyPrints, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by Kevdev
A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.
Design by fgiancarelli
A plectrum printed flat at half a millimetre, 27 mm tall and 24 mm across, with the designer's design across the face - the pun in the name is the whole idea. Thin picks bend more than thick ones, so this is the one for strumming rather than for shredding. Designed by marshal.meacham and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.
Design by marshal.meacham
A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.
Design by printerforge
A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.
Design by Forged in Filament
A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.
Design by osamutake
