3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A dart-shaped glider printed as one piece: 24 cm nose to tail, 15.8 cm across the wings, 12 mm at its thickest, and about 7 g of plastic. It prints flat, so the whole plane lifts off the plate as one object with nothing to glue together - and being flat it takes a minute or two of plastic rather than a flight. A desk toy that looks like folded paper and will not crease, soak up a puddle or blow off a table. Designed by By_Menen and released into the public domain (CC0 1.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by By_Menen

A bulldozer blade for a clog, with a toothed cutting edge and the brackets that hold it on: 81 mm across and 60 mm high, sold as a pair, one for each shoe. Shown as a render of the printable model, not a photograph.

Design by HazEyedeas

A pair of thin earrings, each 1.4" x 1.6" and about 2 mm thick, so they print as one small plate in a couple of minutes and weigh almost nothing on your ears. The pair is one item - the price is for both. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render, not a photo.

Design by Vulcain

A 3-digit combination padlock as a kit card: every part prints flat, mounted on the card, and snaps off it. 4.5" x 3" and about 14 g with the card. Shown as a render of the printable model, not a photograph.

Design by LoboCNC

A V-plow that clamps over the front of a clog: two mirrored blades, 118 mm long and 58 mm high, one for each shoe, that push snow aside as you walk. Shown as a render of the printable model, not a photograph.

Design by OVERTUREFilament

A strip that threads onto a guitar strap and holds a stack of picks, so a fresh one is within reach in the middle of a song: 100 mm long and 25 mm wide, printed in one piece. It sits on the strap rather than in a pocket, which is where picks go to be lost. Designed by willywidget and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by willywidget

Hide and seek, fifty times over: fifty numbered ducks, each with its own number cut into it, and a case to hide them in. Buy the fifty ducks on their own, or the case on its own - the case is 5.7" by 3.8" and holds the lot. Shown as a render, not a photo.

Design by TuscaroraTech

A jitterbug mechanism: a foldable polyhedron in print-in-place segments that flips inside out when you squeeze it. One is about 1.8" x 1.6", and printed as one piece there is nothing to assemble. Sold as one jitterbug - the plate in the picture prints four. Shown as a render of the printable model, not a photograph.

Design by osamutake

A hockey stick lying across a puck, with the round plug that pushes it into a clog: 48 mm across, 13 mm from the shoe to the top of the stick, printed as the charm and its plug together. Shown as a render of the printable model, not a photograph.

Design by hudsonch79

A dragon-scale egg that opens into two halves, one nested inside the other, with a printed shaker bead rattling in the middle: 47 mm across and 62 mm tall, an Easter egg that is a maraca as well as an ornament. The two halves print on one plate with the bead, and the file pauses at the colour change so the shell can come out in one colour and the dragon scale inside in another. Designed by ThrottleXdesign - a remix four links deep of the Original Dragon Egg by Studio YBL and tonyyoungblood - and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by ThrottleXdesign

A cat curled up as a charm, cut in flat relief so the shape reads at a glance on a keyring or a necklace. It prints flat with no supports and measures about 2.4" by 1.8". Shown as a render, not a photo.

Design by dominator334

A fried egg 45 mm across, the yolk standing proud of a wavy white, plus the small plug that snaps behind it into a shoe. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A palm-sized egg shaker for small hands: 40 mm across and 57 mm tall, printed as one closed shell with the rattle sealed inside, so it shakes without anything coming loose that a toddler could get at. Two of them and a kitchen is a percussion section. Designed by craftygirl21 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by craftygirl21

Take-away clickers: a burger, a box of fries and a drink cup, each printed as two halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.5" across - or four of any mix come at the bulk rate. Shown as a render, not a photo.

Design by iNkosi3D

Varsity letters as keychains: a block letter with a stitched look, cut in relief and about 2.4" tall. Pick the letter you want - A to M are here, and each has a hole at the top for a keyring or a chain. Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A soft-serve cone as a shoe charm: a 53 mm cone of waffle ridges under a swirl, with the plug behind it that pushes into a clog. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.

Design by MakerShed

Six horse silhouettes as keychains, each a different pose cut in relief and each with a hole at the top for a ring or a chain. Pick the horse you want - they print flat with no supports and measure about 2.4" by 1.5". Shown as a render, not a photo.

Design by dominator334

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

A crocodile in a straw hat and eyepatch, cut flat with four plugs behind it so it sits on top of a shoe: 33 x 29 mm. Shown as a render of the printable model, not a photograph.

Design by jstoner98

A modular glasses stand: a round 143 mm base with a spindle, a post that carries two long arms, and a cradle that stacks on the spindle, so two pairs or a shelf-full can be kept upright and out of the way. The arms take frames by the bridge and the base is heavy enough not to tip when one pair comes off. Designed by Rockthered and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Rockthered

A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.

Design by TinkerTogether

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

A star that spins: the points are cut so it turns on its axis in the hand and keeps turning. Shown as a render, not a photo.

Design by CreaitivityStudio

A stackable glasses stand: a fin that the cradles slide onto, so the tower grows to whatever height the collection needs. The cradles come in three widths - 67, 77 and 87 mm - and each holds one pair nose-down by the bridge, which suits slim readers and deep sunglass frames alike. The plate prints a whole tower's worth of parts, 167 by 199 mm laid out as the designer arranges it. Designed by Badger Sound Forge and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Badger Sound Forge

Christmas cone fidgets: a spiral cone that runs down through your fingers, and a Santa hat built the same way with its own spiral inside the brim. Pick the one you want - both print as a single piece and stand about 2.8" tall. Shown as a render, not a photo.

Design by Nerdherder

A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.

Design by ArmadilloFDM

Love hearts, one letter at a time: A to M, each a heart-shaped charm with the letter cut into it, so a name or a message is spelled out a charm at a time. About 1.6" by 1.6" each, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

An inner cone passes right through an outer one and neither of them comes apart - that is the whole trick, and it prints as a single piece. Roll it in your hands and the two bodies slide past each other, which is the part that keeps fingers busy. Printed in two colours the cones separate in the eye and the pass-through reads as impossible; printed in one it looks like a solid cone until it moves. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by What3d

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

Six St Patrick's Day charms from one plate: a clover, a horseshoe, a leprechaun hat, a shamrock shield, an Irish banner and a pot of gold. Pick the one you want - each has a hole at the top for a keyring or a chain, prints flat with no supports, and measures about 2" across. Shown as a render, not a photo.

Design by dominator334

A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.

Design by user_3738174853

Two cats curled into a heart, cut in relief so the tails make the shape. Pick the fitting: the keychain has a ring hole, the charm is sized for a chain. It prints flat with no supports, about 1.9" by 2". Shown as a render, not a photo.

Design by dominator334

A small articulated dragon: body and tail cut into segments joined by print-in-place hinges, so it curls through your fingers. Shown as a render, not a photo.

Design by BashStudio3D

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A coffee cup for a keyring, complete with a lid and a sleeve, small enough to disappear in a pocket and clear enough in shape to read at a glance. 0.8" across and printed in one piece. Shown as a render, not a photo.

Design by Tuscarora Tech

Halloween tokens that flip and slide: a disc in a frame that turns over in the hand and clicks through a stop, in five designs from a small 2.6" ghost to a wide 3.4" one. Pick the token you want - each prints in one piece with the disc already in its frame. Shown as a render, not a photo.

Design by Toddy's Trinkets

Six dog charms with a bit more detail in them - a bone, a ball and a few breeds, each cut in relief. Pick the one you want: every charm has a hole at the top for a keyring or a chain, prints flat, and measures about 2" by 2.4". Shown as a render, not a photo.

Design by dominator334

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A mini hockey stick for your keys, printed flat in one piece and shaped like the real thing: a shaft that tapers, a blade turned off it at the lie a real stick uses, a heel that rounds into the shaft and a toe that narrows and leans back. The name is cut into the blade along its length, where a stick carries its brand, and roxium.ca is cut along the shaft underneath - both personalized rather than raised, because a keychain gets rattled around in a pocket and raised lettering wears off first. Type the name you want while you are adding it to the cart and it is cut for you - up to 10 characters, +$5 a piece, charged on top of whatever the stick costs, the volume rate included. A personalized stick is cut to order, so it is paid online rather than reserved for cash at pickup. Leave the name blank and it comes with ROXIUM on the blade. The picture is a render of the printable model - real photographs of the print go up once the first one is cut.

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A tiny dino for a keyring, all of an inch tall, printed flat in one piece. Shown as a render, not a photo.

Design by SG3D

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja