One colour costs less than multi-colour · No HST, sitewide.
$2.56Was $3.78
A planetary gear set printed in place: six small gears mesh between a sun gear and a toothed ring, so turning any one of them turns all the rest. It is 2.5" across and prints as a single piece with nothing to snap together. Shown as a render, not a photo.
Design by HurtTree
$3.92Was $5.80
An inner cone passes right through an outer one and neither of them comes apart - that is the whole trick, and it prints as a single piece. Roll it in your hands and the two bodies slide past each other, which is the part that keeps fingers busy. Printed in two colours the cones separate in the eye and the pass-through reads as impossible; printed in one it looks like a solid cone until it moves. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by What3d
$1.25Was $1.99
A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.
Design by PrintcessJacqueline3DDesigns
$1.34Was $1.99
A phone stand that folds out of a keychain: the plate swings up and the phone leans back on it, and folded away it hangs on your keys. Shown as a render, not a photo.
Design by musielovsky
$2.11Was $3.12
A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.
Design by Morganja
$1.96Was $2.90
A clicker keychain with four buttons that press and click, printed in place so nothing needs assembling. Shown as a render, not a photo.
Design by Print3DFamilyFidgets
$2.89Was $4.28
A hexagonal tube cut into one continuous spiral, so it springs and flexes in the hand and the turns of the helix roll past each other under a thumb. It prints as a single piece and needs no assembly, and it stands 2.8" tall by 1.3" across. Shown as a render, not a photo.
Design by NerdHerder
$12.50Was $18.52
A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.
Design by JEP0405
$1.34Was $1.99
A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.
Design by Morganja
$1.34Was $1.99
A small articulated dragon: body and tail cut into segments joined by print-in-place hinges, so it curls through your fingers. Shown as a render, not a photo.
Design by BashStudio3D
$1.34Was $1.99
A tiny dino for a keyring, all of an inch tall, printed flat in one piece. Shown as a render, not a photo.
Design by SG3D
$14.31Was $21.20
A star that spins: the points are cut so it turns on its axis in the hand and keeps turning. Shown as a render, not a photo.
Design by CreaitivityStudio
$1.35Was $2.00
A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.
Design by Morganja
$1.34Was $1.99
A frog that jumps: press its back and it springs off the table, and the pond bowl catches it. Pick the frog on its own or the bowl with it - the bowl is 5" across, and three frogs fit on one plate if you want a set. Shown as a render, not a photo.
Design by Niski
$1.34Was $1.99
An axolotl with its frilly gills out and a smile, printed in one piece with no AMS and no supports. 3.5" long, so it sits on a desk or rides along as a keyring charm. Shown as a render, not a photo.
Design by AmandaRoos
$3.74Was $5.54
An octopus with eight arms that trail behind it and a round head with two eyes on top - printed in one piece, no supports. 5.2" across the arms, and big enough to sit on a desk rather than in a pocket. Shown as a render, not a photo.
Design by Davis_County_Library
$1.34Was $1.99
A jellyfish with a dome for a head and four little tentacles, printed in place on a round stand so it hovers on a desk. 2.3" across the stand, printed as one piece with the tentacles already free. Shown as a render, not a photo.
Design by slavko
$1.34Was $1.99
A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.
Design by MeltedMoose
