3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A small articulated dragon: body and tail cut into segments joined by print-in-place hinges, so it curls through your fingers. Shown as a render, not a photo.

Design by BashStudio3D

Halloween tokens that flip and slide: a disc in a frame that turns over in the hand and clicks through a stop, in five designs from a small 2.6" ghost to a wide 3.4" one. Pick the token you want - each prints in one piece with the disc already in its frame. Shown as a render, not a photo.

Design by Toddy's Trinkets

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A tiny dino for a keyring, all of an inch tall, printed flat in one piece. Shown as a render, not a photo.

Design by SG3D

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

A clicker keychain with four buttons that press and click, printed in place so nothing needs assembling. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

An eight-legged octopus printed in one piece with its legs already articulated: no supports, no assembly, and it wriggles the moment it comes off the plate. Small enough for a desk or a pocket, and the designer's own profile runs it at 0.16 mm layers, two walls and 8% infill. It takes a two-colour silk filament especially well, which is how the designer's sample is printed. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Timmy_1293

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A fox printed as a chain of flexing segments - pointed ears, a bushy tail and a loop through the tail for a keyring - so it curls in a pocket and springs back. 4.2" nose to tail, printed in one piece. Shown as a render, not a photo.

Design by OrangeSs

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A fat little frog printed as one piece, every joint already moving, so it sits on its haunches and waddles about when you nudge it. 1.5" across, in one colour or two. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by TinkerLink

The flexi rex as a keychain: a chain of articulated segments with a loop through the tail, so it jingles and curls in a pocket. 2.5" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by LukesWorkshopBuilds

A dragon in a coiled pose, wings half-open and tail curling round to its head - a display piece rather than a toy. 9.5" across and the biggest thing on the shelf, printed in one piece. Shown as a render, not a photo.

Design by mdesign

A slug that ripples: a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. Two sizes - 3.5" and 5.2" long - each printed in one piece with no supports. Remixed by Elite_1650 from Teque5's "Friendly Articulated Slug", sold under the same licence. Shown as a render, not a photo.

Design by Elite_1650

A baby hippo printed as a chain of articulated segments - stubby legs, a rounded snout and a tail - so it waddles about on a desk and settles into whatever pose you leave it in. 1.4" long, printed in one piece with no supports, in one colour or painted. Remixed by Joshuaisodd from Whitney Richmond's "Baby Hippo", sold under the same licence. Shown as a render, not a photo.

Design by Joshuaisodd

The articulated dragon shrunk to pocket size: a chain of segments, a plated back and a tail that curls round to the head. 5.2" long, printed in one piece, and small enough to live in a bag. Shown as a render, not a photo.

Design by MeltyBits

A dinosaur that looks knitted rather than moulded - cable ribs down its back, a stitched belly and little knitted feet - printed as one piece. 3.0" long, and the stitch texture is the print itself, not a pattern painted on. Shown as a render, not a photo.

Design by hjs19

The full-size articulated dragon: plated spine, wings folded along its back, and a chain of joints from nose to tail so it coils around a monitor or a wrist. 7.0" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by Freddie

A rubber-band fly swatter gun: stretch the band, aim and let go, and it fires the swatter head across the room. Printed flat in five parts with no supports, about 5.2" long. Remixed by 123木头人 from uhltimate's original Fly Swatter Gun. Shown as a render, not a photo.

Design by 123木头人

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

A bag clip shaped like a cat, with a spring jaw that holds a chip bag or a coffee pouch shut. 1.6" across, printed in place in one piece - the hinge comes off the plate already working. Shown as a render, not a photo.

Design by Muuurt

A gecko printed as a chain of articulated segments, with its toes splayed and its tail trailing, so it drapes over a shelf edge and stays there. 5.1" from nose to tail, printed in one piece with no supports and nothing to assemble. Shown as a render, not a photo.

Design by Timmy_1293

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

Nine flat dinosaur shapes, 1.6 mm thick and about 4" across, printed as a sheet you colour in and stand up. A pack for a rainy afternoon: colour them, cut them out, stick them to the fridge. Shown as a render, not a photo.

Design by Merilno3D

A dolphin that looks knitted and bends like a chain - stitches down the back, a fin and a tail that flex. 2.5" long, printed in one piece with a hole through the tail for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by OrangeSs

A little bear printed as a chain of flexing segments, with a loop through the top for a keyring - no supports anywhere. 2.2" tall, printed in one piece, and it wriggles when you hold it by the tail. Shown as a render, not a photo.

Design by TinkerLink

A jumping spider, joints and all, with a loop through the top for a keyring - eight legs that fold under it and a body that moves when you hold the ring. 2.4" across, printed in one piece. Shown as a render, not a photo.

Design by Daann_ii

A starfish printed in place, with five arms that already move on the plate and a face on top. 2.2" across, printed as one piece with no supports and nothing to assemble. Shown as a render, not a photo.

Design by slavko

A jellyfish with a dome for a head and four little tentacles, printed in place on a round stand so it hovers on a desk. 2.3" across the stand, printed as one piece with the tentacles already free. Shown as a render, not a photo.

Design by slavko

A little snake printed in one piece with no AMS and no supports, coiled so it sits up on its own tail. 2.5" long and about 2 g of plastic - a desk pet, or a whole plate of them for a market stall. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AmandaRoos

A baby dragon sitting up with its little wings folded and its tail wrapped round its feet. 2.1" tall, printed in one piece with no supports, so it stands on a desk on its own. Shown as a render, not a photo.

Design by CLUCKWORKS3D

An orca printed in place: the body and its fins come off the plate as one piece that already moves. 2.4" long, with the eye patch and the white belly reading in black and white filament. Shown as a render, not a photo.

Design by slavko

An octopus with eight arms that trail behind it and a round head with two eyes on top - printed in one piece, no supports. 5.2" across the arms, and big enough to sit on a desk rather than in a pocket. Shown as a render, not a photo.

Design by Davis_County_Library

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A ruler that folds: nineteen 160 mm segments that hinge end to end, plus the two end caps, so it measures a room and then folds down to a pocket. The full set is 19 segments; the smaller option is the same design at 70 per cent, which is the one for a desk drawer. Shown as a render, not a photo.

Design by PenguinPrototypes

A Christmas cookie stamp and its matching cutter: press the stamp into the dough and the outline cuts clean around it, so the icing has a line to follow. 3.1" across, printed as two pieces - stamp and cutter. Shown as a render, not a photo.

Design by P2T

A frog that jumps: press its back and it springs off the table, and the pond bowl catches it. Pick the frog on its own or the bowl with it - the bowl is 5" across, and three frogs fit on one plate if you want a set. Shown as a render, not a photo.

Design by Niski

An axolotl with its frilly gills out and a smile, printed in one piece with no AMS and no supports. 3.5" long, so it sits on a desk or rides along as a keyring charm. Shown as a render, not a photo.

Design by AmandaRoos