3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

An abstract crucifix: the figure flows into the cross in one smooth line, pared down to the gesture rather than the detail. Three sizes in the one design family, 9.8", 9.3" and 8.6" at their longest - each sold on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3dKingpin

A small portrait keychain, modelled as a relief so the face reads at a glance. 2.4" x 3.1", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by lira3d

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.

Design by pain.killer.2

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

A race medal with a moulded ribbon and a numbered disc in the middle. The file holds first, second and third, so a set covers a whole podium for a school race or a party game. The picture is a render of the printable model, not a photograph of a finished print.

Design by Rodrigo Ferriz

A bookmark shaped like an alligator, with the jaw clipping over the page and the body lying in the gutter - so it marks the page and the line at once. 3.9" long, printed as a body and a jaw. Shown as a render, not a photo.

Design by 3dprinting

A cross worn as a keychain: Jesus on the front, JESUS down the beam, and a molded loop at the top for a split ring. 3.9" tall and 2.4" across the arms, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Christ Art

A screw-top capsule for the small things that have to stay dry: matches, pills, a spare battery, a couple of picks. A loop on the cap hangs it from a backpack or a bike frame. Six sizes, 48 mm at the smallest and 128 mm at the largest, each printing as a container and its cap with no supports. The designer's optional TPU gasket - the part that makes it properly waterproof - is not something the shop prints, so as printed the thread keeps splashes and pocket lint out rather than a soaking. Designed by squinn and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by squinn

A little hand that clips onto the page and points at the exact line you stopped on - so a bookmark marks where you are, not just which page. 2.8" long, printed flat with the fingers already free. Shown as a render, not a photo.

Design by helder.bernardo

A can cap that opens the can as well: press it over the top of a standard 355 ml tab can and the drink is covered between sips, with the opener moulded into the same part. It prints in one piece in about forty minutes with no supports. Designed by BUD THE RETIRED PRINT GUY and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by BUD THE RETIRED PRINT GUY

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

A lid that presses onto an open drinks can and slides shut, keeping dust, wasps and debris out of a beer or a soda between sips. Two fits are on offer: the standard can, whose lid measures 1.4 by 1.9 inches, and a wider one at 1.5 by 2.4 inches for a fatter 16 oz rim. Each prints as a lid and its sliding cover, and the standard lid also comes in the designer's looser-fitting version for a can that runs tight. Designed by Tiger prints, who remixed EcoDad's Printables lid - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Tiger prints

A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.

Design by DanyP86