3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A cat curled up as a charm, cut in flat relief so the shape reads at a glance on a keyring or a necklace. It prints flat with no supports and measures about 2.4" by 1.8". Shown as a render, not a photo.

Design by dominator334

A fried egg 45 mm across, the yolk standing proud of a wavy white, plus the small plug that snaps behind it into a shoe. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

Varsity letters as keychains: a block letter with a stitched look, cut in relief and about 2.4" tall. Pick the letter you want - A to M are here, and each has a hole at the top for a keyring or a chain. Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A soft-serve cone as a shoe charm: a 53 mm cone of waffle ridges under a swirl, with the plug behind it that pushes into a clog. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Abz

A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.

Design by MakerShed

Six horse silhouettes as keychains, each a different pose cut in relief and each with a hole at the top for a ring or a chain. Pick the horse you want - they print flat with no supports and measure about 2.4" by 1.5". Shown as a render, not a photo.

Design by dominator334

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

A crocodile in a straw hat and eyepatch, cut flat with four plugs behind it so it sits on top of a shoe: 33 x 29 mm. Shown as a render of the printable model, not a photograph.

Design by jstoner98

A modular glasses stand: a round 143 mm base with a spindle, a post that carries two long arms, and a cradle that stacks on the spindle, so two pairs or a shelf-full can be kept upright and out of the way. The arms take frames by the bridge and the base is heavy enough not to tip when one pair comes off. Designed by Rockthered and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Rockthered

A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.

Design by TinkerTogether

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

A star that spins: the points are cut so it turns on its axis in the hand and keeps turning. Shown as a render, not a photo.

Design by CreaitivityStudio

A vase with a wave running up its wall - a single spiralling surface, so the ridges catch the light differently as you walk past it. 180 mm tall, and shaped for dried flowers, pampas, feathers, or for nothing at all in a bare corner. It wants a dry arrangement rather than water. Print it in a silk or a matte filament and the waves do the rest of the work. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A stackable glasses stand: a fin that the cradles slide onto, so the tower grows to whatever height the collection needs. The cradles come in three widths - 67, 77 and 87 mm - and each holds one pair nose-down by the bridge, which suits slim readers and deep sunglass frames alike. The plate prints a whole tower's worth of parts, 167 by 199 mm laid out as the designer arranges it. Designed by Badger Sound Forge and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Badger Sound Forge

A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.

Design by ArmadilloFDM

Love hearts, one letter at a time: A to M, each a heart-shaped charm with the letter cut into it, so a name or a message is spelled out a charm at a time. About 1.6" by 1.6" each, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

An inner cone passes right through an outer one and neither of them comes apart - that is the whole trick, and it prints as a single piece. Roll it in your hands and the two bodies slide past each other, which is the part that keeps fingers busy. Printed in two colours the cones separate in the eye and the pass-through reads as impossible; printed in one it looks like a solid cone until it moves. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by What3d

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

A little cauldron with a lid full of bubbles, sized to sit over a battery tea light: the light comes up through the bubbles and the whole thing glows. It prints in two parts, the cauldron and its top, so the top can be a different colour from the pot - the designer printed the tops in plain white and let the tea light do the colour. About 70 to 77 mm tall once the two parts are together. Battery tea light only, never a real flame. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DJH665

Six St Patrick's Day charms from one plate: a clover, a horseshoe, a leprechaun hat, a shamrock shield, an Irish banner and a pot of gold. Pick the one you want - each has a hole at the top for a keyring or a chain, prints flat with no supports, and measures about 2" across. Shown as a render, not a photo.

Design by dominator334

A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.

Design by user_3738174853

Two cats curled into a heart, cut in relief so the tails make the shape. Pick the fitting: the keychain has a ring hole, the charm is sized for a chain. It prints flat with no supports, about 1.9" by 2". Shown as a render, not a photo.

Design by dominator334

One little ghost, three sizes of it: Small is 35 mm tall, Medium 45 mm and Large 64 mm, so a shelf can gather a few rather than carry a loner. Each prints as a rounded little spectre with a friendly face and no supports. Every ghost is its own object on the plate, so no multi-colour printer is needed - print them in different colours and they arrive as a set. The small one disappears into a bowl by the door; the large still fits in a hand. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

Candle holders that let the light out through the walls: a Voronoi web of gaps and ridges so the flame - a battery tealight, never a real one - glows through the whole shell rather than out of the top. The set is three holders, three diffusers and the base plate that carries them; print the holders in matte black and the diffusers in white, which is the pairing the designer built it around, and a single holder works just as well on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A little bear holding a heart, printed in one piece with the heart standing proud of its chest. Shown as a render, not a photo.

Design by davide7seven

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A coffee cup for a keyring, complete with a lid and a sleeve, small enough to disappear in a pocket and clear enough in shape to read at a glance. 0.8" across and printed in one piece. Shown as a render, not a photo.

Design by Tuscarora Tech

Six dog charms with a bit more detail in them - a bone, a ball and a few breeds, each cut in relief. Pick the one you want: every charm has a hole at the top for a keyring or a chain, prints flat, and measures about 2" by 2.4". Shown as a render, not a photo.

Design by dominator334

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A mini hockey stick for your keys, printed flat in one piece and shaped like the real thing: a shaft that tapers, a blade turned off it at the lie a real stick uses, a heel that rounds into the shaft and a toe that narrows and leans back. The name is cut into the blade along its length, where a stick carries its brand, and roxium.ca is cut along the shaft underneath - both personalized rather than raised, because a keychain gets rattled around in a pocket and raised lettering wears off first. Type the name you want while you are adding it to the cart and it is cut for you - up to 10 characters, +$5 a piece, charged on top of whatever the stick costs, the volume rate included. A personalized stick is cut to order, so it is paid online rather than reserved for cash at pickup. Leave the name blank and it comes with ROXIUM on the blade. The picture is a render of the printable model - real photographs of the print go up once the first one is cut.

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A low-poly heart, faceted like cut stone: the low-poly build keeps it light and lets it catch the light along the facets, and it stands on its own on a shelf. 3.4" wide, printed in one piece. Shown as a render, not a photo.

Design by Creaitivity Studio

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A cat curled into a charm, cut as a flat silhouette with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A tall vase with a drop falling through its wall, and the tray that holds it: the designer made it for a single stem or a bundle of dried grass, and the tray catches whatever you drop in it, which is where the mindfulness comes in. Printed as two pieces - the vase and its holder - so you can use them together as an arrangement or keep the tray on a desk for rings, keys and incense. Standing 24 cm, it wants a shelf with headroom or the middle of a table. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

A DAD heart gyro fidget: a heart with DAD cut through it, mounted so it spins in the frame when you flick it. 1.8" by 2.2", printed in one piece with the pin already in place. Shown as a render, not a photo.

Design by LangHjornArt

Five heart shapes, each layered front to back so the colours read as depth: black sits at the back as the outline and the two layers in front are yours to choose, so one colour is the simplest and three makes it pop. Pick the shape you want - each is about 1.6" by 1.5", with a loop for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A clicker keychain with four buttons that press and click, printed in place so nothing needs assembling. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

An elephant charm in flat relief, trunk curled, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017