3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A vase drawn for spiral vase mode: one continuous wall spiralling up from the foot to the lip, so it prints in a single unbroken pass with no seam, and a light behind it shows the twist. Designed by elio196721 and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by elio196721

Five draped ghosts, each with cut eyes and a mouth and each hollow underneath, so it sits over a battery LED tealight and glows from the inside with the light showing through the cutouts. They print as five separate pieces at slightly different sizes, so they can be scattered along a table, a shelf or a porch step - the set is all five. An LED tealight only, as the designer intends: a real flame would soften the plastic. Designed by kappern and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by kappern

A butterfly cut from one flat plate, wings spread to about 9.5 inches across, with the wing veins and the row of spots opened right through so the wall colour shows in them. It hangs flat against a wall, a window frame or the back of a door, where a shelf ornament would not fit. Sold as the single printed piece. Designed by VK3DWorks and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by VK3DWorks

A rose and its stem printed as one piece, so there is no assembly at the end: the petals spiral out of the bud and the stem runs down to a base that stands on a desk. The designer prints it as a classic print rather than vase mode, and suggests one perimeter and no infill with a transparent filament if you want the light to come through the petals. The page credits Lytta and RubixDragon for the roses it was built from - all three designers are named on this page. Printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by user_531694306

The word HOME in a heavy serif with the O drawn as a heart, cut as one flat piece. It comes in two arrangements: a horizontal strip for a shelf edge, a letterbox gap or the space over a door, and a vertical stack with the letters over two lines for a narrow wall. Each is printed as one piece - sold in whichever arrangement you choose. Designed by saya3design and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), exactly as published. Shown as a render of the printable model, not a photograph.

Design by saya3design

Cats in silhouette for the wall: four printed pieces - three frames, each with a cat, and one butterfly that hangs between them - every shape cut from 5 mm, so they hang as a set and can be arranged the way your wall wants them. The designer prints them in matte black or another strong plain colour, because the outline is the whole picture. Sold as the set. Designed by carlos_peral and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by carlos_peral

A tree-shaped photo frame: a heart in the middle and branches around it holding small photographs, with the plates that back them printed alongside so the pictures stay in without glue or tape. The designer scaled the pieces so the larger tree prints on one sheet, and suggests an acetate sheet in front of each photo to keep the dust off. Sold as the printed set. Designed by PediMR and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by PediMR

A small star that spins: the arms are printed in place, so the star turns in the hand or on a desk, and at 28 mm across it is a pocket fidget rather than a desk toy. No AMS needed - it prints in one colour. Designed by Amanda Roos and printed under Creative Commons Public Domain; the designer asks only to be mentioned when it is sold, which this listing does. Shown as a render of the printable model, not a photograph.

Design by Amanda Roos

A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.

Design by ZHeights

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A small articulated dragon: body and tail cut into segments joined by print-in-place hinges, so it curls through your fingers. Shown as a render, not a photo.

Design by BashStudio3D

A tiny dino for a keyring, all of an inch tall, printed flat in one piece. Shown as a render, not a photo.

Design by SG3D

An axolotl with its frilly gills out and a smile, printed in one piece with no AMS and no supports. 3.5" long, so it sits on a desk or rides along as a keyring charm. Shown as a render, not a photo.

Design by AmandaRoos

An octopus with eight arms that trail behind it and a round head with two eyes on top - printed in one piece, no supports. 5.2" across the arms, and big enough to sit on a desk rather than in a pocket. Shown as a render, not a photo.

Design by Davis_County_Library

A jellyfish with a dome for a head and four little tentacles, printed in place on a round stand so it hovers on a desk. 2.3" across the stand, printed as one piece with the tentacles already free. Shown as a render, not a photo.

Design by slavko