3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Twelve little pals off one plate, each about two inches across and printed as a single piece, with no supports and nothing to assemble. Pick the one you want - the size on each chip is that pal's own width by height, so a 2.8"x1.6" one is a different creature from a 2.0"x1.4". Shown as a render, not a photo.

Design by Apricity

A little octopus printed as a chain of flexing segments, so its eight arms trail and curl behind it. 2.2" across, printed in one piece in a single colour or with the body and the arms in different ones. Shown as a render, not a photo.

Design by slavko

A baby spike dragon with a ridged back and a curled tail, small enough to sit on a desk or ride on a keyring. 1.9" long, printed in one piece at high detail. Shown as a render, not a photo.

Design by BashStudio3D

A 2 mm PLA cake stencil, 6 x 4 inches, with Happy Birthday and three balloons cut right through. The lettering is a stencil face, so the middles of the a, p, B, R and D stay attached to the plaque instead of falling out. Lay it on a sheet of parchment over the cake, dust with cocoa or icing sugar, and lift it away. Four or more come at the bulk rate. The picture is a render of the printable model, not a photograph; real photos go up once the first one is printed.

A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.

Design by AmandaRoos

Three holders that keep bottles lying down in the fridge instead of rolling out of the door - each cradles one bottle on its side and stacks with the others. The plate prints three, and each is about 9.4" long. Shown as a render, not a photo.

Design by RossMacAllan

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A little alligator printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles across the desk and settles into whatever shape you leave it in. 2.4" long, printed in one piece. Shown as a render, not a photo.

Design by Litolunar

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

An Easter egg in two halves that spiral into each other: you twist one into the other and the spiral holds, so the egg is a toy as much as an ornament, and it comes apart again. Sold as the two-part egg. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

An egg with a door in it: the front opens and shuts on a hinge printed in place, so the little house egg can be opened as often as you like - the designer notes the first opening needs a gentle pull to snap the hinge free. Printed in the flat-bottomed version the designer supplies, so it stands. Designed by AcmeArt and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by AcmeArt

An articulated cat printed as one piece: the segments print with gaps between them, so it bends and curls in the hand and stands up to being carried around. The eyes are part of the same print. Designed by Xeraj, who remixed feketeimre's Flexi Cat - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Xeraj

Ballasted track sections for the Dragon Railway at 1/64: six straight lengths from 50 mm to 300 mm, each printed with its ballast shoulder moulded on, so a layout needs no loose gravel. The set is the six lengths the designer's plate holds, and his recommended minimum radius is 400 mm. The curved sections live in his second file, which prints a whole loop at once - that is a custom print rather than a shelf item, so ask for a quote and the shop will run the curves you need. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A top that keeps going: a heavy rim, a fine point and a printed handle to spin it between finger and thumb. 2.1" across, about 41 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by happybirthday

A 1/64 scale tanker for the Dragon Railway: the tank, its chassis, walkway and bogies across three plates, about 98 g of plastic. The designer's own profile runs 0.08 mm layers, for the surface the model deserves. It runs on the Dragon Railway bogies and autocouplers, which are separate prints. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A Happy Birthday stencil for cakes and cookies: the words cut through a thin plate, so icing, cocoa or dusting sugar goes on through it. 3.9" wide, about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A slender dragon printed as a chain of spiky segments that flex and curl, with a horned head at one end - detailed all down its back and small enough to carry. 6.5" long, printed in one piece with every joint already free. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A small star that spins: the arms are printed in place, so the star turns in the hand or on a desk, and at 28 mm across it is a pocket fidget rather than a desk toy. No AMS needed - it prints in one colour. Designed by Amanda Roos and printed under Creative Commons Public Domain; the designer asks only to be mentioned when it is sold, which this listing does. Shown as a render of the printable model, not a photograph.

Design by Amanda Roos

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

The smallest flexi dragon the shop carries: a chunky little dragon of rounded segments that wiggle end to end, claws and all. 2.1" long and barely over a gram of plastic, printed in one piece - a natural market-table giveaway. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A small dragon on a printed chain: plated back, a curled tail and a head that turns, all articulated from the plate. 6.1" long - long enough to drape over a monitor, small enough to carry. Shown as a render, not a photo.

Design by SHF3D.

A spider printed flat as one piece with every leg already jointed, so it walks across a table when you nudge it and folds up small. 4.6" across, about 5 g of plastic. Shown as a render, not a photo.

Design by mieldeprot

An impossible passthrough wound as a spiral: the helical parts turn through each other and hold, printed in one piece. 2.8" tall, about 29 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by MoltenPlastic3D

A print-in-place finger catapult: two halves that come off the plate already joined, with a sprung arm that flicks a small pellet across the desk. 3.1" long, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by somtru

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A pair of eighth notes, each an outline rather than a filled shape, so they stay light on the ear and catch the light along the stem. Each is 20 x 22.7 mm and 2 mm thick, with the hole in the note head for a hook, and they print mirrored so the two notes sit opposite each other. Shown as a render of the printable model, not a photograph.

Design by mikesak29

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A watermelon slice with the rind standing proud of the flesh and the seeds cut into it, 26.7 x 25.9 mm and 1.6 mm thick with a hole at the top for a hook. The plate prints eight slices, which is four pairs; order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A bee with a rounded body, two wings standing off it and a hook hole at the head, printed as one piece at 25 x 29 mm. The body is domed rather than flat, so it reads as a bee from the side too, and it is light enough to wear all day. Order a pair and you get two. Shown as a render of the printable model, not a photograph.

Design by wally

A butterfly with its wings open and the veins left raised, so the pattern survives printing instead of filling in. Each is 49 x 31 mm and 1.6 mm thick, thin enough to sit flat against the ear, with a hole at the top for a hook. The pair prints as two mirrored butterflies. Shown as a render of the printable model, not a photograph.

Design by FrazierSmith

A dinosaur cut into interlocking jigsaw pieces and sold as the whole set: twelve chunky pieces, printed flat in PLA, that push together into the animal and come apart again. Two editions, cut differently from the same artwork - Adult and Kid, with the Kid edition's tabs cut larger for smaller hands. Both print as a set with no supports and nothing to glue, and the loose pieces store as the shape they make. The Adult set is about 322 g of plastic and the Kid set about 352 g, so each one is a multi-plate print rather than an afternoon. Designed by oymate and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oymate

A round spider web in a ring, with every strand cut through so the web is open and a spider sits in the middle of it. Each is about 44 x 48 mm and 2.2 mm thick, with a loop at the top for a hook, and both webs print together as one piece. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Four feather shapes, each printed twice so every design makes a mirrored pair: 60 mm long, 2 mm thick, with the barbs cut through so the feather is an outline and the quill shows. Printed flat with no supports. The plate holds all eight earrings - the whole set of four pairs - and they come in one colour. Shown as a render of the printable model, not a photograph.

Design by KameleonForge

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

A small desk novelty in two parts, 2.5" x 2.6" x 0.8", printed as one plate. Shown as a render of the printable model, not a photograph.

Design by LoboCNC

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

One pointed charm: an 18 mm cone on a flat base that presses into the hole of a clog, 13 mm across. Shown as a render of the printable model, not a photograph.

Design by ntalekt

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A dart-shaped glider printed as one piece: 24 cm nose to tail, 15.8 cm across the wings, 12 mm at its thickest, and about 7 g of plastic. It prints flat, so the whole plane lifts off the plate as one object with nothing to glue together - and being flat it takes a minute or two of plastic rather than a flight. A desk toy that looks like folded paper and will not crease, soak up a puddle or blow off a table. Designed by By_Menen and released into the public domain (CC0 1.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by By_Menen

A bulldozer blade for a clog, with a toothed cutting edge and the brackets that hold it on: 81 mm across and 60 mm high, sold as a pair, one for each shoe. Shown as a render of the printable model, not a photograph.

Design by HazEyedeas