3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A fidget spinner small enough to live in a pocket: one piece, no bearings, no axle to glue, printed in place so the two halves and their weights come off the plate ready to spin. It is a 15-minute print in the designer's own profile, which is why it makes a good giveaway or market-stock item. Printed in a silk filament the spinning face catches the light. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DragonFusion3D

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

A paw that rides on top of a straw: the straw passes through the middle of it, the paw sits above the lid, and the raised pad and four toes catch the light as the cup moves. It is made for the 10 mm Stanley straws, 3.5" tall by 1.6" across, and it prints in one piece. Shown as a render, not a photo.

Design by Morganja

A pair of leaf earrings: a pointed leaf with its veins cut into the face, light enough to wear all day at a bit over a gram the pair. They print flat with a hole at the top for the hook, so nothing else is needed but the ear wire. Each is 1.9" by 0.8". The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render, not a photo.

Design by C4UStudio

A cat curled up as a charm, cut in flat relief so the shape reads at a glance on a keyring or a necklace. It prints flat with no supports and measures about 2.4" by 1.8". Shown as a render, not a photo.

Design by dominator334

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

Varsity letters as keychains: a block letter with a stitched look, cut in relief and about 2.4" tall. Pick the letter you want - A to M are here, and each has a hole at the top for a keyring or a chain. Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

Six St Patrick's Day charms from one plate: a clover, a horseshoe, a leprechaun hat, a shamrock shield, an Irish banner and a pot of gold. Pick the one you want - each has a hole at the top for a keyring or a chain, prints flat with no supports, and measures about 2" across. Shown as a render, not a photo.

Design by dominator334

Three round pet pendants struck like coins, each with a loop at the top for a chain or a keyring and each about 1.7" by 2". The set is all three, printed flat so the faces come out crisp. Shown as a render, not a photo.

Design by dominator334

Two cats curled into a heart, cut in relief so the tails make the shape. Pick the fitting: the keychain has a ring hole, the charm is sized for a chain. It prints flat with no supports, about 1.9" by 2". Shown as a render, not a photo.

Design by dominator334

A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.

Design by ArmadilloFDM

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

Candle holders that let the light out through the walls: a Voronoi web of gaps and ridges so the flame - a battery tealight, never a real one - glows through the whole shell rather than out of the top. The set is three holders, three diffusers and the base plate that carries them; print the holders in matte black and the diffusers in white, which is the pairing the designer built it around, and a single holder works just as well on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.

Design by user_3738174853

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A mini hockey stick for your keys, printed flat in one piece and shaped like the real thing: a shaft that tapers, a blade turned off it at the lie a real stick uses, a heel that rounds into the shaft and a toe that narrows and leans back. The name is cut into the blade along its length, where a stick carries its brand, and roxium.ca is cut along the shaft underneath - both personalized rather than raised, because a keychain gets rattled around in a pocket and raised lettering wears off first. Type the name you want while you are adding it to the cart and it is cut for you - up to 10 characters, +$5 a piece, charged on top of whatever the stick costs, the volume rate included. A personalized stick is cut to order, so it is paid online rather than reserved for cash at pickup. Leave the name blank and it comes with ROXIUM on the blade. The picture is a render of the printable model - real photographs of the print go up once the first one is cut.

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

A pen holder clad in raised dragon scales, hexagonal all the way round, with a smooth inner cup for pens, pencils or brushes. 3.1" across and 4" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3DWoosh

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A bow tie printed as an open voronoi lattice, light enough to wear and unlike any fabric one - the knot is part of the same one-piece print. 4.5" across. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by alexlluch

A Happy Birthday picture frame with the words cut around the border and a little cake-and-candles motif at the top - it prints as a matched pair, ready to hold a photo or a card from the party. Each frame is 5.3 x 3.7", about 123 g for the pair. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

A cursive Happy Birthday cake topper on a long stake, the script joined end to end so it prints flat and stands tall in a cake. 6" across the words, about 10 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by nxbalazs

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A block-letter Happy Birthday banner: chunky script letters standing on a base strip with a candle and balloon tucked in among them, printed flat as one piece. 6.3" wide, about 27 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A thin calligraphic Happy Birthday topper, the loops and swashes joined into one delicate piece that lies across a cake. 5.4" at its widest and under 4 mm thick, about 15 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ana Bonacho

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

Happy Birthday with a rod and reel behind the words: a fishing birthday in one flat piece that stands up in the cake. 6.7" wide, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano