3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A pumpkin with the face cut right through, so a tealight inside throws the grin onto the wall rather than just glowing. 3.9" tall, printed in one piece - drop a battery tealight in the base and it lights the whole face. Shown as a render, not a photo.

Design by PentillyCrafts

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by LilÕJimbob

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Weso2976

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

A small ghost holding a tealight: the flame glows through the shell and out of the eyes, so the whole figure lights up. 3" tall, about 12 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A largemouth bass on a rock, mouth open, fins up, printed as one piece with the base built in: a shelf or desk piece for somebody who would rather be on the water. Two sizes, and both are measured off the designer's own files - 97 mm nose to tail, and 190 mm for the mantelpiece. The smaller one is the same mesh scaled down and supported, so the detail is the same at both sizes. Designed by AUTROJAN and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by AUTROJAN

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by dhs

A medal rack: two upright spines joined to a flat back plate, with a hooked arm either side of each spine so medals hang in a row instead of sliding into a heap, and the back takes a screw or a strip of tape. About 9.5 inches wide - a whole season of races hangs off it. Designed by donnkey - a remix, in their words, of Alan Břuska's "Věšák na medaile - Medal hanger" on Printables - and printed under CC0. Shown as a render of the printable model, not a photograph.

Design by donnkey

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A vase drawn for spiral vase mode: one continuous wall spiralling up from the foot to the lip, so it prints in a single unbroken pass with no seam, and a light behind it shows the twist. Designed by elio196721 and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by elio196721

Five draped ghosts, each with cut eyes and a mouth and each hollow underneath, so it sits over a battery LED tealight and glows from the inside with the light showing through the cutouts. They print as five separate pieces at slightly different sizes, so they can be scattered along a table, a shelf or a porch step - the set is all five. An LED tealight only, as the designer intends: a real flame would soften the plastic. Designed by kappern and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by kappern

A butterfly cut from one flat plate, wings spread to about 9.5 inches across, with the wing veins and the row of spots opened right through so the wall colour shows in them. It hangs flat against a wall, a window frame or the back of a door, where a shelf ornament would not fit. Sold as the single printed piece. Designed by VK3DWorks and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by VK3DWorks

A rose and its stem printed as one piece, so there is no assembly at the end: the petals spiral out of the bud and the stem runs down to a base that stands on a desk. The designer prints it as a classic print rather than vase mode, and suggests one perimeter and no infill with a transparent filament if you want the light to come through the petals. The page credits Lytta and RubixDragon for the roses it was built from - all three designers are named on this page. Printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by user_531694306

The word HOME in a heavy serif with the O drawn as a heart, cut as one flat piece. It comes in two arrangements: a horizontal strip for a shelf edge, a letterbox gap or the space over a door, and a vertical stack with the letters over two lines for a narrow wall. Each is printed as one piece - sold in whichever arrangement you choose. Designed by saya3design and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), exactly as published. Shown as a render of the printable model, not a photograph.

Design by saya3design

Cats in silhouette for the wall: four printed pieces - three frames, each with a cat, and one butterfly that hangs between them - every shape cut from 5 mm, so they hang as a set and can be arranged the way your wall wants them. The designer prints them in matte black or another strong plain colour, because the outline is the whole picture. Sold as the set. Designed by carlos_peral and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by carlos_peral

A table number: the digit cut as one flat plate inside an ornate oval frame, standing in a round base. Pick the number you need - every digit from 0 to 9 - and it arrives as the frame and its base, ready to slot together. About 5 inches tall, so it reads from across a room without sitting between two guests. Designed by swirly1007, who made the set for their daughter's wedding, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by swirly1007

A tree-shaped photo frame: a heart in the middle and branches around it holding small photographs, with the plates that back them printed alongside so the pictures stay in without glue or tape. The designer scaled the pieces so the larger tree prints on one sheet, and suggests an acetate sheet in front of each photo to keep the dust off. Sold as the printed set. Designed by PediMR and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by PediMR

A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.

Design by ZHeights

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.

Design by Morganja

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose