3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A soft-serve cone as a shoe charm: a 53 mm cone of waffle ridges under a swirl, with the plug behind it that pushes into a clog. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

Six horse silhouettes as keychains, each a different pose cut in relief and each with a hole at the top for a ring or a chain. Pick the horse you want - they print flat with no supports and measure about 2.4" by 1.5". Shown as a render, not a photo.

Design by dominator334

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

A crocodile in a straw hat and eyepatch, cut flat with four plugs behind it so it sits on top of a shoe: 33 x 29 mm. Shown as a render of the printable model, not a photograph.

Design by jstoner98

A vase with a wave running up its wall - a single spiralling surface, so the ridges catch the light differently as you walk past it. 180 mm tall, and shaped for dried flowers, pampas, feathers, or for nothing at all in a bare corner. It wants a dry arrangement rather than water. Print it in a silk or a matte filament and the waves do the rest of the work. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

Love hearts, one letter at a time: A to M, each a heart-shaped charm with the letter cut into it, so a name or a message is spelled out a charm at a time. About 1.6" by 1.6" each, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A little cauldron with a lid full of bubbles, sized to sit over a battery tea light: the light comes up through the bubbles and the whole thing glows. It prints in two parts, the cauldron and its top, so the top can be a different colour from the pot - the designer printed the tops in plain white and let the tea light do the colour. About 70 to 77 mm tall once the two parts are together. Battery tea light only, never a real flame. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DJH665

Six St Patrick's Day charms from one plate: a clover, a horseshoe, a leprechaun hat, a shamrock shield, an Irish banner and a pot of gold. Pick the one you want - each has a hole at the top for a keyring or a chain, prints flat with no supports, and measures about 2" across. Shown as a render, not a photo.

Design by dominator334

Two cats curled into a heart, cut in relief so the tails make the shape. Pick the fitting: the keychain has a ring hole, the charm is sized for a chain. It prints flat with no supports, about 1.9" by 2". Shown as a render, not a photo.

Design by dominator334

One little ghost, three sizes of it: Small is 35 mm tall, Medium 45 mm and Large 64 mm, so a shelf can gather a few rather than carry a loner. Each prints as a rounded little spectre with a friendly face and no supports. Every ghost is its own object on the plate, so no multi-colour printer is needed - print them in different colours and they arrive as a set. The small one disappears into a bowl by the door; the large still fits in a hand. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

Candle holders that let the light out through the walls: a Voronoi web of gaps and ridges so the flame - a battery tealight, never a real one - glows through the whole shell rather than out of the top. The set is three holders, three diffusers and the base plate that carries them; print the holders in matte black and the diffusers in white, which is the pairing the designer built it around, and a single holder works just as well on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A little bear holding a heart, printed in one piece with the heart standing proud of its chest. Shown as a render, not a photo.

Design by davide7seven

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A coffee cup for a keyring, complete with a lid and a sleeve, small enough to disappear in a pocket and clear enough in shape to read at a glance. 0.8" across and printed in one piece. Shown as a render, not a photo.

Design by Tuscarora Tech

Six dog charms with a bit more detail in them - a bone, a ball and a few breeds, each cut in relief. Pick the one you want: every charm has a hole at the top for a keyring or a chain, prints flat, and measures about 2" by 2.4". Shown as a render, not a photo.

Design by dominator334

A mini hockey stick for your keys, printed flat in one piece and shaped like the real thing: a shaft that tapers, a blade turned off it at the lie a real stick uses, a heel that rounds into the shaft and a toe that narrows and leans back. The name is cut into the blade along its length, where a stick carries its brand, and roxium.ca is cut along the shaft underneath - both personalized rather than raised, because a keychain gets rattled around in a pocket and raised lettering wears off first. Type the name you want while you are adding it to the cart and it is cut for you - up to 10 characters, +$5 a piece, charged on top of whatever the stick costs, the volume rate included. A personalized stick is cut to order, so it is paid online rather than reserved for cash at pickup. Leave the name blank and it comes with ROXIUM on the blade. The picture is a render of the printable model - real photographs of the print go up once the first one is cut.

A low-poly heart, faceted like cut stone: the low-poly build keeps it light and lets it catch the light along the facets, and it stands on its own on a shelf. 3.4" wide, printed in one piece. Shown as a render, not a photo.

Design by Creaitivity Studio

A cat curled into a charm, cut as a flat silhouette with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A tall vase with a drop falling through its wall, and the tray that holds it: the designer made it for a single stem or a bundle of dried grass, and the tray catches whatever you drop in it, which is where the mindfulness comes in. Printed as two pieces - the vase and its holder - so you can use them together as an arrangement or keep the tray on a desk for rings, keys and incense. Standing 24 cm, it wants a shelf with headroom or the middle of a table. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A DAD heart gyro fidget: a heart with DAD cut through it, mounted so it spins in the frame when you flick it. 1.8" by 2.2", printed in one piece with the pin already in place. Shown as a render, not a photo.

Design by LangHjornArt

Five heart shapes, each layered front to back so the colours read as depth: black sits at the back as the outline and the two layers in front are yours to choose, so one colour is the simplest and three makes it pop. Pick the shape you want - each is about 1.6" by 1.5", with a loop for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

An elephant charm in flat relief, trunk curled, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.

Design by porkac