3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A mini hockey stick for your keys, printed flat in one piece and shaped like the real thing: a shaft that tapers, a blade turned off it at the lie a real stick uses, a heel that rounds into the shaft and a toe that narrows and leans back. The name is cut into the blade along its length, where a stick carries its brand, and roxium.ca is cut along the shaft underneath - both personalized rather than raised, because a keychain gets rattled around in a pocket and raised lettering wears off first. Type the name you want while you are adding it to the cart and it is cut for you - up to 10 characters, +$5 a piece, charged on top of whatever the stick costs, the volume rate included. A personalized stick is cut to order, so it is paid online rather than reserved for cash at pickup. Leave the name blank and it comes with ROXIUM on the blade. The picture is a render of the printable model - real photographs of the print go up once the first one is cut.

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A bow tie printed as an open voronoi lattice, light enough to wear and unlike any fabric one - the knot is part of the same one-piece print. 4.5" across. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by alexlluch

A Happy Birthday picture frame with the words cut around the border and a little cake-and-candles motif at the top - it prints as a matched pair, ready to hold a photo or a card from the party. Each frame is 5.3 x 3.7", about 123 g for the pair. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

A cursive Happy Birthday cake topper on a long stake, the script joined end to end so it prints flat and stands tall in a cake. 6" across the words, about 10 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by nxbalazs

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A block-letter Happy Birthday banner: chunky script letters standing on a base strip with a candle and balloon tucked in among them, printed flat as one piece. 6.3" wide, about 27 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

A thin calligraphic Happy Birthday topper, the loops and swashes joined into one delicate piece that lies across a cake. 5.4" at its widest and under 4 mm thick, about 15 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ana Bonacho

Happy Birthday with a rod and reel behind the words: a fishing birthday in one flat piece that stands up in the cake. 6.7" wide, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A Happy Birthday cake topper with a footballer mid-kick: the words arc over a ball and two net posts, cut as one flat piece that stands in the cake. 5" wide, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

A cross worn as a keychain: Jesus on the front, JESUS down the beam, and a molded loop at the top for a split ring. 3.9" tall and 2.4" across the arms, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Christ Art

An abstract crucifix: the figure flows into the cross in one smooth line, pared down to the gesture rather than the detail. Three sizes in the one design family, 9.8", 9.3" and 8.6" at their longest - each sold on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3dKingpin

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A Happy Birthday stencil for cakes and cookies: the words cut through a thin plate, so icing, cocoa or dusting sugar goes on through it. 3.9" wide, about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A football cake topper - a player, a ball and the words Happy Birthday - printed flat as one piece that stands in the cake. 5.5" wide, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Regata

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

A hinged box for rings and earrings, 150 by 83 by 20 mm closed: a tray with compartments, a lid that shuts on printed hinges, and two pins that press in to hold the hinge line - four printed parts, no screws, no supports. Small enough for a wash bag and rigid enough to keep its shape. A remix of "Parametric hinged small parts box" by Billiam on Printables, which is CC BY 4.0, and designed by Ivan Chamberlain under Creative Commons Attribution 4.0 (CC BY 4.0) - both are credited. Shown as a render of the printable model, not a photograph.

Design by Ivan Chamberlain

Happy Birthday for a cyclist: a bicycle and rider over the words, cut flat and standing in the cake. 7" wide, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

An LP on the wall: a back plate with a shelf the cover stands on and two brackets that hold the record upright in front of it, so the sleeve and the disc are both on show. 218 by 214 mm and 187 mm deep, printed as one piece. Designed by LucMonnom and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by LucMonnom

A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A record sleeve stands on a ledge under a patterned back panel, and the ledge carries NOW PLAYING across its face in relief, so the record on the shelf is announced rather than guessed at. 200 mm wide and 159 mm tall - wide enough for a 12 inch sleeve - printed in one piece with no supports under the sign. Designed by Kosmok and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Kosmok

A strip that threads onto a guitar strap and holds a stack of picks, so a fresh one is within reach in the middle of a song: 100 mm long and 25 mm wide, printed in one piece. It sits on the strap rather than in a pocket, which is where picks go to be lost. Designed by willywidget and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by willywidget

A capo in two printed parts: a jaw that sits across the strings and the lever that clamps it down, 92 mm wide so it spans a standard six-string fretboard. It goes on the neck above the fret and holds the strings at the new position, which is what lets one shape be played in any key. Designed by Kevdev, a remix of the Guitar Capo by HarleyPrints, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Kevdev

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A plate of music notes cut flat at 3 mm: single quavers, beamed pairs, a dotted note and the odd small rest, from 25 mm up to 67 mm long, so a wall, a noticeboard or the front of a piano can be dressed with them. They print lying down, which means no supports and a clean face straight off the plate. Designed by EcneNomma and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by EcneNomma

A plectrum printed flat at half a millimetre, 27 mm tall and 24 mm across, with the designer's design across the face - the pun in the name is the whole idea. Thin picks bend more than thick ones, so this is the one for strumming rather than for shredding. Designed by marshal.meacham and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by marshal.meacham

A small square gift box, about 60 mm across and 50 mm deep, with a lid that sits a little proud on purpose so it lifts off easily. The bow and the little tree decoration print as separate pieces, so the box can be used plain or dressed up - all four pieces come as the set, and there is room inside for a ring, a pair of earrings or a few chocolates. Designed by Lunavixen and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Lunavixen

A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by gareth7562

A rail that a CD jewel case stands in, ribbed along its length so the case leans back instead of sliding forward, on four short feet that keep the disc off the shelf. 149 mm wide and 30 mm tall - the width of a standard case, with a little room either side. Designed by ToToKia and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by ToToKia

Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by SF3DPrints

A fish for the wall, cut flat: a simple fishing silhouette that the designer reshaped slightly to make it print cleanly. At 238 by 166 mm it is big enough to hold a wall on its own - a shed, a cabin, or the wall of somebody who would rather be fishing. Designed by MazziNiX and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by MazziNiX

A heart with a knitted texture - cable rows and ribs moulded into both faces - printed as one piece so it flexes in the hand: the segments print in place with a clearance between them, and nothing has to be assembled. About 3 inches across, which sits on a desk or in a gift box. Designed by HistoricalPiecesandMore and released under CC0. Shown as a render of the printable model, not a photograph.

Design by HistoricalPiecesandMore

An Easter egg in two halves that spiral into each other: you twist one into the other and the spiral holds, so the egg is a toy as much as an ornament, and it comes apart again. Sold as the two-part egg. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A practice mute for trombone, printed in three parts: the long tapered body that goes down into the bell, the flared cup that caps it, and the small collar that keeps the two together. 250 mm long and 193 mm across the cup, so it takes a full-size bell. The cup is what does the muting, so the horn can be played in an apartment without the neighbours learning the set list. Designed by 烤肉大师 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by 烤肉大师

A bunny built from flat planes: the low-poly faceting catches the light on every angle, and at 40 mm tall it is a small figure for a shelf, a windowsill or an Easter table. Printed in one piece. Designed by Pejdro and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by Pejdro

A heart standing on a base with wedding rings resting against the top - the designer sets them into the part that touches the heart and suggests turning on ironing, or moving them to whichever face you prefer. A small piece for an anniversary shelf or a wedding table. Designed by bambaxp and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by bambaxp

An egg with twisted ribs running from pole to pole, printed in one piece. The ribs catch the light as it turns, and it stands on its base rather than rolling off the table. About 3 inches tall - a table piece, a basket filler, or something to hand a child instead of chocolate. Designed by OrangeSs and released under CC0. Shown as a render of the printable model, not a photograph.

Design by OrangeSs

Eight sports-ball charms, each with the ball's own surface cut into it - soccer pentagons, a golf ball's dimples, a basketball's seams - so they read as the real thing at charm size. Pick the one you want: every ball has a hole for a keyring or a chain, prints flat with no supports, and measures about 1.7" by 2". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A layered volleyball charm: the ball's panels are cut as separate raised layers, so the seams read as depth rather than a printed line. It is 1.6" by 1.4", has a hole at the top for a ring or a chain, and prints flat in one piece. Shown as a render, not a photo.

Design by CoisinhasdaManu

The classic folded awareness ribbon with a keyring loop at the top, printed flat so the fold reads cleanly on both faces. It is 2.5" long by 1.4" wide and prints in whatever colour you choose. Shown as a render, not a photo.

Design by Miss3DP