3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

A pen holder clad in raised dragon scales, hexagonal all the way round, with a smooth inner cup for pens, pencils or brushes. 3.1" across and 4" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3DWoosh

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Weso2976

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

A T-rex skull as a five-part model: the skull, its lower jaw, the pins that hinge the jaw, and a stand for it. The larger skull runs about 8" front to back, and the jaw opens on its pins. Shown as a render of the printable model, not a photograph.

Design by Monster_Zero

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

A top that keeps going: a heavy rim, a fine point and a printed handle to spin it between finger and thumb. 2.1" across, about 41 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by happybirthday

Two strands twisted around each other into a pen stand: a double helix about 22 cm tall on a 14 cm square base, printed in one piece with nothing to assemble. Pens drop into the gaps between the rungs and lean out along the twist, so a handful of them fan apart instead of clumping together in a cup - and the base is wide enough that a full stand does not tip. Empty, it is a desk ornament rather than a mug with pens in it, which is most of what a pen holder does all day. Printed in PLA at a 0.2 mm layer, about 34 g of plastic. Designed by AndreUser and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AndreUser

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A medal rack: two upright spines joined to a flat back plate, with a hooked arm either side of each spine so medals hang in a row instead of sliding into a heap, and the back takes a screw or a strip of tape. About 9.5 inches wide - a whole season of races hangs off it. Designed by donnkey - a remix, in their words, of Alan Břuska's "Věšák na medaile - Medal hanger" on Printables - and printed under CC0. Shown as a render of the printable model, not a photograph.

Design by donnkey

A stackable glasses stand: a fin that the cradles slide onto, so the tower grows to whatever height the collection needs. The cradles come in three widths - 67, 77 and 87 mm - and each holds one pair nose-down by the bridge, which suits slim readers and deep sunglass frames alike. The plate prints a whole tower's worth of parts, 167 by 199 mm laid out as the designer arranges it. Designed by Badger Sound Forge and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Badger Sound Forge

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A vase drawn for spiral vase mode: one continuous wall spiralling up from the foot to the lip, so it prints in a single unbroken pass with no seam, and a light behind it shows the twist. Designed by elio196721 and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by elio196721

The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Abz

A modular glasses stand: a round 143 mm base with a spindle, a post that carries two long arms, and a cradle that stacks on the spindle, so two pairs or a shelf-full can be kept upright and out of the way. The arms take frames by the bridge and the base is heavy enough not to tip when one pair comes off. Designed by Rockthered and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Rockthered

A butterfly cut from one flat plate, wings spread to about 9.5 inches across, with the wing veins and the row of spots opened right through so the wall colour shows in them. It hangs flat against a wall, a window frame or the back of a door, where a shelf ornament would not fit. Sold as the single printed piece. Designed by VK3DWorks and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by VK3DWorks

A rose and its stem printed as one piece, so there is no assembly at the end: the petals spiral out of the bud and the stem runs down to a base that stands on a desk. The designer prints it as a classic print rather than vase mode, and suggests one perimeter and no infill with a transparent filament if you want the light to come through the petals. The page credits Lytta and RubixDragon for the roses it was built from - all three designers are named on this page. Printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by user_531694306

The word HOME in a heavy serif with the O drawn as a heart, cut as one flat piece. It comes in two arrangements: a horizontal strip for a shelf edge, a letterbox gap or the space over a door, and a vertical stack with the letters over two lines for a narrow wall. Each is printed as one piece - sold in whichever arrangement you choose. Designed by saya3design and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), exactly as published. Shown as a render of the printable model, not a photograph.

Design by saya3design

Cats in silhouette for the wall: four printed pieces - three frames, each with a cat, and one butterfly that hangs between them - every shape cut from 5 mm, so they hang as a set and can be arranged the way your wall wants them. The designer prints them in matte black or another strong plain colour, because the outline is the whole picture. Sold as the set. Designed by carlos_peral and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by carlos_peral

A tree-shaped photo frame: a heart in the middle and branches around it holding small photographs, with the plates that back them printed alongside so the pictures stay in without glue or tape. The designer scaled the pieces so the larger tree prints on one sheet, and suggests an acetate sheet in front of each photo to keep the dust off. Sold as the printed set. Designed by PediMR and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by PediMR

A desk caddy printed in one piece: a raised back that stands a phone at a reading angle, a round well for pens, and a square tray for a watch, keys or a card, with a slot for a charging cable to pass through. It is 7.1" wide by 3.5" deep. Shown as a render, not a photo.

Design by Maker76

A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.

Design by ZHeights