3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Four Jeep charms, each a different model cut in relief and each with a hole at the top for a keyring or a chain. Pick the one you want - they print flat with no supports and measure about 2.4" by 2.4". Shown as a render, not a photo.

Design by dominator334

Mark the shark as a keychain or as a necklace charm - the same shark in two fittings, one with a ring hole and one sized for a chain. It prints flat with no supports, about 2.4" long. Shown as a render, not a photo.

Design by dominator334

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

A crocodile printed as a chain of flexing segments, grin and all, with a ridged back and a tail that whips about. Three sizes - 4.7", 5.6" and 7.5" long - each printed in one piece. Shown as a render, not a photo.

Design by SHF3D

A braid tool: hook the strands through the slot and the plait forms as you pull, so a French braid takes half the time and no third hand. 5.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

A caterpillar printed as a chain of flexing segments with a face at one end, so it wriggles along your hand and curls up when you put it down. 6.7" long, printed in one piece, with no supports and no assembly. Shown as a render, not a photo.

Design by Pistachio

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose

A screw toy for small hands: three chunky bolts with matching nuts, the caps they screw into and a long threaded rod - the plate is the whole set. The rod is 7.1" long, and every part is printed oversized so a toddler can get a grip on it. Shown as a render, not a photo.

Design by hyperZ

Four miniature garden tools - shovel, spade, pitchfork and rake - about 2.8" long, with the hafts and heads modelled properly rather than blobs. A set for a dollhouse garden, a terrarium or a plant shelf. Shown as a render, not a photo.

Design by Gekon3D

A bunny printed as a chain of flexing segments with a carrot to go with it, so it curls up in your hand and springs straight again. The set prints as one plate - a 2.4" bunny and its carrot - and comes in a single colour or with the parts in different ones. Shown as a render, not a photo.

Design by TinkerTogether

A lizard printed in one piece with no AMS and no supports - ridged back, splayed feet and a tail that curls, sitting flat wherever you put it. Three sizes: 1.7", 3.7" and 4.6" long, the smallest small enough for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AmandaRoos

A layered volleyball charm: the ball's panels are cut as separate raised layers, so the seams read as depth rather than a printed line. It is 1.6" by 1.4", has a hole at the top for a ring or a chain, and prints flat in one piece. Shown as a render, not a photo.

Design by CoisinhasdaManu

Eight sports-ball charms, each with the ball's own surface cut into it - soccer pentagons, a golf ball's dimples, a basketball's seams - so they read as the real thing at charm size. Pick the one you want: every ball has a hole for a keyring or a chain, prints flat with no supports, and measures about 1.7" by 2". Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A penguin that comes apart into a stack of rings and goes back together again - the plate carries the body, four rings and the little caps, so it builds up and knocks down like a nesting toy. About 3.6" across the widest ring. Shown as a render, not a photo.

Design by katinkus

A water dragon printed as a chain of flexing segments - ridges along the back, a finned tail, and no supports anywhere. 4.5" long, printed in one piece, and it settles into whatever shape you leave it in. Shown as a render, not a photo.

Design by TinkerTogether

Twelve little pals off one plate, each about two inches across and printed as a single piece, with no supports and nothing to assemble. Pick the one you want - the size on each chip is that pal's own width by height, so a 2.8"x1.6" one is a different creature from a 2.0"x1.4". Shown as a render, not a photo.

Design by Apricity

A little octopus printed as a chain of flexing segments, so its eight arms trail and curl behind it. 2.2" across, printed in one piece in a single colour or with the body and the arms in different ones. Shown as a render, not a photo.

Design by slavko

A baby spike dragon with a ridged back and a curled tail, small enough to sit on a desk or ride on a keyring. 1.9" long, printed in one piece at high detail. Shown as a render, not a photo.

Design by BashStudio3D

A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.

Design by AmandaRoos

A little alligator printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles across the desk and settles into whatever shape you leave it in. 2.4" long, printed in one piece. Shown as a render, not a photo.

Design by Litolunar

Four stencils for painting a brick-built tree scene: layers that line up on a wall or a card, so the trunk and the canopy come out in register. 6.5" square, 0.8 mm thin, printed flat. Shown as a render, not a photo.

Design by Merilno3D

A squeezer that slides up the tube as it empties: the roller presses the paste forward and the key at the end hooks over a rail so the tube hangs. 2.9" long, printed in one piece with the edges rounded so it does not catch on the shelf. Remixed by Weisnetde from two earlier squeezers, all under the same licence. Shown as a render, not a photo.

Design by Weisnetde

A flower-petal stencil 0.8 mm thin, for tracing or airbrushing onto paper, cake or a wall. 3.8" across, printed flat in one piece - thin enough to lie flush on the surface. Shown as a render, not a photo.

Design by Merilno3D

Three stick figures in fighting poses, each one holding your pencil where it would hold a weapon: an archer drawing a pencil like a bow, a spearman resting on a long one, and a sniper kneeling with one as a rifle. The archer takes short pencils of about 8 to 9 cm, the other two take ordinary 10 to 16 cm ones. Sold as the set of three. Designed by Gekko and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Gekko

A heart with a knitted texture - cable rows and ribs moulded into both faces - printed as one piece so it flexes in the hand: the segments print in place with a clearance between them, and nothing has to be assembled. About 3 inches across, which sits on a desk or in a gift box. Designed by HistoricalPiecesandMore and released under CC0. Shown as a render of the printable model, not a photograph.

Design by HistoricalPiecesandMore

Six mushroom shelves, each printed with its wall mount built in - no bracket to add and nothing to glue, so a screw in the wall is the whole installation. The caps come in six shapes and sizes, so they can run up a wall beside a plant or dot about independently. Designed by Dr.D, who remixed Moiras_creations' Mushroom shelves - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Dr.D

A taiko drummer whose drum is the holder: the hollow drum takes cotton swabs, and the figure's hands hold one snapped in half as a pair of drumsticks. Four printed parts - base, figure, drum and the rack behind him - and the drumsticks take a touch of glue to stay put, as the designer's own notes say. Sold as the set. Designed by Benji and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Benji

An Easter egg in two halves that spiral into each other: you twist one into the other and the spiral holds, so the egg is a toy as much as an ornament, and it comes apart again. Sold as the two-part egg. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A small square gift box, about 60 mm across and 50 mm deep, with a lid that sits a little proud on purpose so it lifts off easily. The bow and the little tree decoration print as separate pieces, so the box can be used plain or dressed up - all four pieces come as the set, and there is room inside for a ring, a pair of earrings or a few chocolates. Designed by Lunavixen and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Lunavixen

A medal rack: two upright spines joined to a flat back plate, with a hooked arm either side of each spine so medals hang in a row instead of sliding into a heap, and the back takes a screw or a strip of tape. About 9.5 inches wide - a whole season of races hangs off it. Designed by donnkey - a remix, in their words, of Alan Břuska's "Věšák na medaile - Medal hanger" on Printables - and printed under CC0. Shown as a render of the printable model, not a photograph.

Design by donnkey

An egg with a door in it: the front opens and shuts on a hinge printed in place, so the little house egg can be opened as often as you like - the designer notes the first opening needs a gentle pull to snap the hinge free. Printed in the flat-bottomed version the designer supplies, so it stands. Designed by AcmeArt and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by AcmeArt

An articulated cat printed as one piece: the segments print with gaps between them, so it bends and curls in the hand and stands up to being carried around. The eyes are part of the same print. Designed by Xeraj, who remixed feketeimre's Flexi Cat - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Xeraj

Ballasted track sections for the Dragon Railway at 1/64: six straight lengths from 50 mm to 300 mm, each printed with its ballast shoulder moulded on, so a layout needs no loose gravel. The set is the six lengths the designer's plate holds, and his recommended minimum radius is 400 mm. The curved sections live in his second file, which prints a whole loop at once - that is a custom print rather than a shelf item, so ask for a quote and the shop will run the curves you need. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A top that keeps going: a heavy rim, a fine point and a printed handle to spin it between finger and thumb. 2.1" across, about 41 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by happybirthday

A 1/64 scale tanker for the Dragon Railway: the tank, its chassis, walkway and bogies across three plates, about 98 g of plastic. The designer's own profile runs 0.08 mm layers, for the surface the model deserves. It runs on the Dragon Railway bogies and autocouplers, which are separate prints. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

An egg with twisted ribs running from pole to pole, printed in one piece. The ribs catch the light as it turns, and it stands on its base rather than rolling off the table. About 3 inches tall - a table piece, a basket filler, or something to hand a child instead of chocolate. Designed by OrangeSs and released under CC0. Shown as a render of the printable model, not a photograph.

Design by OrangeSs

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A slender dragon printed as a chain of spiky segments that flex and curl, with a horned head at one end - detailed all down its back and small enough to carry. 6.5" long, printed in one piece with every joint already free. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A small star that spins: the arms are printed in place, so the star turns in the hand or on a desk, and at 28 mm across it is a pocket fidget rather than a desk toy. No AMS needed - it prints in one colour. Designed by Amanda Roos and printed under Creative Commons Public Domain; the designer asks only to be mentioned when it is sold, which this listing does. Shown as a render of the printable model, not a photograph.

Design by Amanda Roos

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

The smallest flexi dragon the shop carries: a chunky little dragon of rounded segments that wiggle end to end, claws and all. 2.1" long and barely over a gram of plastic, printed in one piece - a natural market-table giveaway. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A small dragon on a printed chain: plated back, a curled tail and a head that turns, all articulated from the plate. 6.1" long - long enough to drape over a monitor, small enough to carry. Shown as a render, not a photo.

Design by SHF3D.

A spider printed flat as one piece with every leg already jointed, so it walks across a table when you nudge it and folds up small. 4.6" across, about 5 g of plastic. Shown as a render, not a photo.

Design by mieldeprot

An impossible passthrough wound as a spiral: the helical parts turn through each other and hold, printed in one piece. 2.8" tall, about 29 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by MoltenPlastic3D