3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.

Design by inhabitworker

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by LilÕJimbob

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A largemouth bass on a rock, mouth open, fins up, printed as one piece with the base built in: a shelf or desk piece for somebody who would rather be on the water. Two sizes, and both are measured off the designer's own files - 97 mm nose to tail, and 190 mm for the mantelpiece. The smaller one is the same mesh scaled down and supported, so the detail is the same at both sizes. Designed by AUTROJAN and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by AUTROJAN

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by dhs

A table number: the digit cut as one flat plate inside an ornate oval frame, standing in a round base. Pick the number you need - every digit from 0 to 9 - and it arrives as the frame and its base, ready to slot together. About 5 inches tall, so it reads from across a room without sitting between two guests. Designed by swirly1007, who made the set for their daughter's wedding, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by swirly1007

A hanging books-read counter: a sign with a row of numbers that slide into it, so the count can be moved along as the year goes. It is two plates - the sign with one of each number, and a second sign with the numbers again so the count can pass ten - and either can be bought on its own. Shown as a render, not a photo.

Design by ZHeights

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.

Design by Morganja

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose