3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.

Design by IndigoRaptor

A flat page marker with a fox carved in raised relief across its face - it slides over the page and the design reads against the paper. 9.4" long and 2.7 mm thin, printed flat in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by shadow.lune

A Christmas cookie stamp and its matching cutter: press the stamp into the dough and the outline cuts clean around it, so the icing has a line to follow. 3.1" across, printed as two pieces - stamp and cutter. Shown as a render, not a photo.

Design by P2T

The smallest flexi dragon the shop carries: a chunky little dragon of rounded segments that wiggle end to end, claws and all. 2.1" long and barely over a gram of plastic, printed in one piece - a natural market-table giveaway. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A baby dragon that prints in one piece, with an articulated spine so the neck, wings and tail all bend and the whole thing can drape over a finger. It sits, curls and lies down, and needs no assembly and no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Helios3D

A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by MoltenPlastic3D

A slender dragon printed as a chain of spiky segments that flex and curl, with a horned head at one end - detailed all down its back and small enough to carry. 6.5" long, printed in one piece with every joint already free. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A desk golf set in eleven printed pieces: a green you can rearrange piece by piece, a ball, a club and the furniture around it. About 3" a piece and 115 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SakiSale

A small dragon on a printed chain: plated back, a curled tail and a head that turns, all articulated from the plate. 6.1" long - long enough to drape over a monitor, small enough to carry. Shown as a render, not a photo.

Design by SHF3D.

A spider printed flat as one piece with every leg already jointed, so it walks across a table when you nudge it and folds up small. 4.6" across, about 5 g of plastic. Shown as a render, not a photo.

Design by mieldeprot

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A giraffe lying down with its neck folded back and its legs tucked - printed as a chain of segments, so it flops about when you pick it up. 6.5" long, and the eyes print as separate 8 mm pieces that go in after. Shown as a render, not a photo.

Design by SHF3D.

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

Four Halloween cutters - pumpkin, ghost, bat and the like - about 3" across each, printed with a cutting rim deep enough for biscuit dough or Play-Doh. One plate prints the set. Shown as a render, not a photo.

Design by Creaitivity Studio

An impossible passthrough wound as a spiral: the helical parts turn through each other and hold, printed in one piece. 2.8" tall, about 29 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A little hand that clips onto the page and points at the exact line you stopped on - so a bookmark marks where you are, not just which page. 2.8" long, printed flat with the fingers already free. Shown as a render, not a photo.

Design by helder.bernardo

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A bookmark shaped like an alligator, with the jaw clipping over the page and the body lying in the gutter - so it marks the page and the line at once. 3.9" long, printed as a body and a jaw. Shown as a render, not a photo.

Design by 3dprinting

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A print-in-place finger catapult: two halves that come off the plate already joined, with a sprung arm that flicks a small pellet across the desk. 3.1" long, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by somtru

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A candy machine that turns a canning jar into a dispenser: a base that screws onto the jar's own lid ring, a knob and a printed pin, so no screw is needed anywhere. Fill the jar with sweets, fit the base, turn the knob and a few drop through. The designer also ships a stronger pin for silk PLA, and a second file for the narrower Hema store jar. Designed by carlbelcher and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by carlbelcher

A 1:20 pallet, 50 by 55 mm, for an RC forklift or a shelf of scale freight. It prints with no supports and, at two walls with solid bottom layers, comes out solid through the body. The proportions follow a UK-style pallet rather than a North American one. Designed by CippyO and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by CippyO

A 1/64 scale GP60B diesel for the Dragon Railway: the body, the bogies and the small fittings, printed across five plates, about 191 g of plastic in the set. It is a layout model rather than a toy that survives a floor, and RamBros publishes an assembly manual and a video covering the parts it wants. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

Ballasted track sections for the Dragon Railway at 1/64: six straight lengths from 50 mm to 300 mm, each printed with its ballast shoulder moulded on, so a layout needs no loose gravel. The set is the six lengths the designer's plate holds, and his recommended minimum radius is 400 mm. The curved sections live in his second file, which prints a whole loop at once - that is a custom print rather than a shelf item, so ask for a quote and the shop will run the curves you need. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A 1/64 scale tanker for the Dragon Railway: the tank, its chassis, walkway and bogies across three plates, about 98 g of plastic. The designer's own profile runs 0.08 mm layers, for the surface the model deserves. It runs on the Dragon Railway bogies and autocouplers, which are separate prints. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

An articulated cat printed as one piece: the segments print with gaps between them, so it bends and curls in the hand and stands up to being carried around. The eyes are part of the same print. Designed by Xeraj, who remixed feketeimre's Flexi Cat - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Xeraj

A rose for the top of a 40 oz Stanley cup lid: the bloom prints standing up on the topper, so a plain cup gets a flower on it with nothing to glue in place. It fits the 40 oz lid. Designed by speedster, who remixed Picture_it's blank Stanley lid topper - both makers are credited on this page and both licences are recorded beside the file. Printed under Creative Commons Attribution 4.0 (CC BY 4.0); the topper it is built on is CC BY-SA 4.0, and the print is sold unaltered. Shown as a render of the printable model, not a photograph.

Design by speedster

A blank topper that sits on a 40 oz Stanley cup lid, flat and smooth, so it is a base for whatever goes on top: the designer's own page explains how to add text to it in Bambu Studio, choosing the font and the size and then the colour of the topper and of the writing separately. Sold blank, exactly as published. Designed by Picture_it and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Picture_it

Three stick figures in fighting poses, each one holding your pencil where it would hold a weapon: an archer drawing a pencil like a bow, a spearman resting on a long one, and a sniper kneeling with one as a rifle. The archer takes short pencils of about 8 to 9 cm, the other two take ordinary 10 to 16 cm ones. Sold as the set of three. Designed by Gekko and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Gekko

A baby stone dragon in one piece: the plates of its body are jointed all the way down, so it curls and straightens and holds whatever shape you leave it in, and it stands on its four legs because the legs are part of the same print. This is the wingless one, so nothing catches on a sleeve or a shelf. Two sizes - 4.2 inches and a 2.5 inch pocket-sized version - both printed in place with no supports. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Bash Studio 3D

An articulated baby dragon: the body, tail and neck are cut into segments joined by print-in-place hinges, with the head and its small horns on top. It is 4.5" long and prints in one piece. Choose the finish: solid is the plastic alone, and each extra colour is a filament change at the printer, charged at the shop's $1 a colour. Shown as a render, not a photo.

Design by BashStudio3D

A segmented caterpillar that wriggles: every segment is jointed to the next, printed as one piece with nothing to assemble and no supports, so it comes off the plate already moving. Two lengths - the short one at 5.4 inches and the longer twelve-segment version at 7.2 - and the longer one is the one to buy if you want it to drape and coil in your hand. Prints at 0.2 mm layers in PLA, and it takes a colour change well if you want the segments striped. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Timmy_1293

A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.

Design by TinkerTogether

Christmas cone fidgets: a spiral cone that runs down through your fingers, and a Santa hat built the same way with its own spiral inside the brim. Pick the one you want - both print as a single piece and stand about 2.8" tall. Shown as a render, not a photo.

Design by Nerdherder

A chunky little turtle with a big head, four stubby legs and a tiny tail, and a keyring loop moulded into its shell, so it sits on a desk or dangles off a bag. It is 1.6" by 1.2" and prints in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Type1Printing

Take-away clickers: a burger, a box of fries and a drink cup, each printed as two halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.5" across - or four of any mix come at the bulk rate. Shown as a render, not a photo.

Design by iNkosi3D

A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.

Design by MakerShed

A fidget spinner small enough to live in a pocket: one piece, no bearings, no axle to glue, printed in place so the two halves and their weights come off the plate ready to spin. It is a 15-minute print in the designer's own profile, which is why it makes a good giveaway or market-stock item. Printed in a silk filament the spinning face catches the light. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DragonFusion3D

Hide and seek, fifty times over: fifty numbered ducks, each with its own number cut into it, and a case to hide them in. Buy the fifty ducks on their own, or the case on its own - the case is 5.7" by 3.8" and holds the lot. Shown as a render, not a photo.

Design by TuscaroraTech

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL