3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A soft-serve cone as a shoe charm: a 53 mm cone of waffle ridges under a swirl, with the plug behind it that pushes into a clog. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A fried egg 45 mm across, the yolk standing proud of a wavy white, plus the small plug that snaps behind it into a shoe. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A hockey stick lying across a puck, with the round plug that pushes it into a clog: 48 mm across, 13 mm from the shoe to the top of the stick, printed as the charm and its plug together. Shown as a render of the printable model, not a photograph.

Design by hudsonch79

A Happy Birthday cake topper with a footballer mid-kick: the words arc over a ball and two net posts, cut as one flat piece that stands in the cake. 5" wide, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

Happy Birthday with a rod and reel behind the words: a fishing birthday in one flat piece that stands up in the cake. 6.7" wide, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

A cursive Happy Birthday cake topper on a long stake, the script joined end to end so it prints flat and stands tall in a cake. 6" across the words, about 10 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by nxbalazs

A Happy Birthday picture frame with the words cut around the border and a little cake-and-candles motif at the top - it prints as a matched pair, ready to hold a photo or a card from the party. Each frame is 5.3 x 3.7", about 123 g for the pair. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

A thin calligraphic Happy Birthday topper, the loops and swashes joined into one delicate piece that lies across a cake. 5.4" at its widest and under 4 mm thick, about 15 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ana Bonacho

A block-letter Happy Birthday banner: chunky script letters standing on a base strip with a candle and balloon tucked in among them, printed flat as one piece. 6.3" wide, about 27 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Samiluno

A bow tie printed as an open voronoi lattice, light enough to wear and unlike any fabric one - the knot is part of the same one-piece print. 4.5" across. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by alexlluch

A Happy Birthday stencil for cakes and cookies: the words cut through a thin plate, so icing, cocoa or dusting sugar goes on through it. 3.9" wide, about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

A football cake topper - a player, a ball and the words Happy Birthday - printed flat as one piece that stands in the cake. 5.5" wide, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Regata

Happy Birthday for a cyclist: a bicycle and rider over the words, cut flat and standing in the cake. 7" wide, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Deco Dejw

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A DAD heart gyro fidget: a heart with DAD cut through it, mounted so it spins in the frame when you flick it. 1.8" by 2.2", printed in one piece with the pin already in place. Shown as a render, not a photo.

Design by LangHjornArt

A cat curled into a charm, cut as a flat silhouette with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

An elephant charm in flat relief, trunk curled, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

Six dog charms with a bit more detail in them - a bone, a ball and a few breeds, each cut in relief. Pick the one you want: every charm has a hole at the top for a keyring or a chain, prints flat, and measures about 2" by 2.4". Shown as a render, not a photo.

Design by dominator334

A coffee cup for a keyring, complete with a lid and a sleeve, small enough to disappear in a pocket and clear enough in shape to read at a glance. 0.8" across and printed in one piece. Shown as a render, not a photo.

Design by Tuscarora Tech

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A little bear holding a heart, printed in one piece with the heart standing proud of its chest. Shown as a render, not a photo.

Design by davide7seven

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A low-poly heart, faceted like cut stone: the low-poly build keeps it light and lets it catch the light along the facets, and it stands on its own on a shelf. 3.4" wide, printed in one piece. Shown as a render, not a photo.

Design by Creaitivity Studio

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A mini hockey stick for your keys, printed flat in one piece and shaped like the real thing: a shaft that tapers, a blade turned off it at the lie a real stick uses, a heel that rounds into the shaft and a toe that narrows and leans back. The name is cut into the blade along its length, where a stick carries its brand, and roxium.ca is cut along the shaft underneath - both personalized rather than raised, because a keychain gets rattled around in a pocket and raised lettering wears off first. Type the name you want while you are adding it to the cart and it is cut for you - up to 10 characters, +$5 a piece, charged on top of whatever the stick costs, the volume rate included. A personalized stick is cut to order, so it is paid online rather than reserved for cash at pickup. Leave the name blank and it comes with ROXIUM on the blade. The picture is a render of the printable model - real photographs of the print go up once the first one is cut.

Love hearts, one letter at a time: A to M, each a heart-shaped charm with the letter cut into it, so a name or a message is spelled out a charm at a time. About 1.6" by 1.6" each, with a hole at the top for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Candle holders that let the light out through the walls: a Voronoi web of gaps and ridges so the flame - a battery tealight, never a real one - glows through the whole shell rather than out of the top. The set is three holders, three diffusers and the base plate that carries them; print the holders in matte black and the diffusers in white, which is the pairing the designer built it around, and a single holder works just as well on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

Two cats curled into a heart, cut in relief so the tails make the shape. Pick the fitting: the keychain has a ring hole, the charm is sized for a chain. It prints flat with no supports, about 1.9" by 2". Shown as a render, not a photo.

Design by dominator334

Six St Patrick's Day charms from one plate: a clover, a horseshoe, a leprechaun hat, a shamrock shield, an Irish banner and a pot of gold. Pick the one you want - each has a hole at the top for a keyring or a chain, prints flat with no supports, and measures about 2" across. Shown as a render, not a photo.

Design by dominator334

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

A pair of eighth notes, each an outline rather than a filled shape, so they stay light on the ear and catch the light along the stem. Each is 20 x 22.7 mm and 2 mm thick, with the hole in the note head for a hook, and they print mirrored so the two notes sit opposite each other. Shown as a render of the printable model, not a photograph.

Design by mikesak29

A heart drawn in a few asymmetric arcs, 34 x 29 mm and 2.3 mm thick, with a hole at the top for a hook. The plate is a solid rim around a cut-out centre, so it reads as a sketch of a heart rather than a filled one, and the pair hangs light. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

Two flip flops printed as one piece, each with a raised strap and a toe post standing up through the sole, so they read as sandals rather than flat outlines. Each is about 30 mm long with a hole at the heel for a hook, and the pair comes off the plate together. Shown as a render of the printable model, not a photograph.

Design by tomo3D