3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A vortex vase whose wall spirals in one continuous swirl from base to off-centre mouth, so it looks like it is still turning. 5.4" tall over a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by LilÕJimbob

A pair of little seated figures, each holding a round planter bowl - set them side by side on a windowsill with a succulent, a tea light or loose change in each cup. The two span 7.9" together and print from one file at about 103 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by cr_seb_olarte

Four miniature garden tools - shovel, spade, pitchfork and rake - about 2.8" long, with the hafts and heads modelled properly rather than blobs. A set for a dollhouse garden, a terrarium or a plant shelf. Shown as a render, not a photo.

Design by Gekon3D

A small Japandi-style vase: a rounded bulb wrapped in fine vertical ribs, narrowing to a small open neck, so a single stem stands upright in it. 3.1" tall across a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A three-part seed germinator - base, insert and lid - 4.5" x 5.5" and 20 mm deep, printed in whatever colour you pick. Shown as a render of the printable model, not a photograph.

Design by 3dmonios

A modular hydroponic tower printed as twelve parts: a base, the column that stacks, five growing cups and the plates that close the sides. The column is 220 mm across and 128 mm tall, each cup 55 mm. The modules come apart, so a tower can be built one section at a time and taken down again. Shown as a render of the printable model, not a photograph.

Design by user_139533078

A largemouth bass on a rock, mouth open, fins up, printed as one piece with the base built in: a shelf or desk piece for somebody who would rather be on the water. Two sizes, and both are measured off the designer's own files - 97 mm nose to tail, and 190 mm for the mantelpiece. The smaller one is the same mesh scaled down and supported, so the detail is the same at both sizes. Designed by AUTROJAN and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by AUTROJAN

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A mosquito trap that uses a jar you already have: a funnel that drops into a mason jar's mouth, so a jar of water and a spoon of sugar becomes a trap. The cone lets a mosquito in and the jar's own walls keep it there. Three funnels come off the plate, 76 mm across and 47 mm tall, for the jar sizes the designer covered - standard jam jars among them. Designed by IanFoulds, a remix of the Mosquito Trap by Urasxman, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by IanFoulds

A mid-century planter with vertical ribs and its own drip tray, printed at 0.24 mm layers with two walls and 8 per cent infill - the profile the designer recommends for the balance between speed and detail. He also notes a 0.6 mm nozzle does the same job faster and builds just as solid, and that the model scales cleanly if you want it bigger. Designed by Nordic Creativa and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by Nordic Creativa

A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by dhs

Six mushroom shelves, each printed with its wall mount built in - no bracket to add and nothing to glue, so a screw in the wall is the whole installation. The caps come in six shapes and sizes, so they can run up a wall beside a plant or dot about independently. Designed by Dr.D, who remixed Moiras_creations' Mushroom shelves - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Dr.D

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A table number: the digit cut as one flat plate inside an ornate oval frame, standing in a round base. Pick the number you need - every digit from 0 to 9 - and it arrives as the frame and its base, ready to slot together. About 5 inches tall, so it reads from across a room without sitting between two guests. Designed by swirly1007, who made the set for their daughter's wedding, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by swirly1007

A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.

Design by Morganja

A round indoor pot with a pleated, fabric-like skirt, standing on its own matching base so it can be moved without leaving a ring on the shelf. Two pieces, both printed in the same colour, 4.6" wide and 3" tall together. Shown as a render, not a photo.

Design by NordicCreativa

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose