3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by gareth7562

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A mushroom charm in three pieces that press together: a domed cap, the gills under it and a stem with fixing pegs. Printing it in parts lets the cap take one colour and the stem another, and the assembled charm is about 23 mm tall and 13 mm across with a hole in the cap for a hook. Shown as a render of the printable model, not a photograph.

Design by iNkosi3D

A rail that a CD jewel case stands in, ribbed along its length so the case leans back instead of sliding forward, on four short feet that keep the disc off the shelf. 149 mm wide and 30 mm tall - the width of a standard case, with a little room either side. Designed by ToToKia and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by ToToKia

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

A butterfly drawn as one continuous line and cut 1.5 mm thick at 150 x 160 mm, so it sits on a wall as a shape that casts a shadow rather than a solid plaque. It prints flat in one piece with no supports and needs no fixings: mounting putty or a pin behind the body is enough. Shown as a render of the printable model, not a photograph.

Design by PediM

A heart built from two nested outlines, so it reads as a heart from across a room and stays light on the ear. Each is 33 x 32.4 mm and 4.1 mm thick at the join, with a hole at the top for a hook, and the plate prints four hearts, which is two pairs. Shown as a render of the printable model, not a photograph.

Design by Fetter79

A molar with a smiling face cut into it, in two sizes: 30 x 23 mm and 25 x 18 mm, with a hole at the crown for a hook. A gift for a dentist, a hygienist, or anyone who likes a tooth with a face on it. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by HaPeHu

A plate of music notes cut flat at 3 mm: single quavers, beamed pairs, a dotted note and the odd small rest, from 25 mm up to 67 mm long, so a wall, a noticeboard or the front of a piano can be dressed with them. They print lying down, which means no supports and a clean face straight off the plate. Designed by EcneNomma and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by EcneNomma

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A paw print with four toe pads and a deep heel pad, cut 2.3 mm thick so the pads stay proud of the outline instead of blurring into it. Each paw is 23 x 24.5 mm with a hole between the toes for a hook, and the pair is mirrored so the prints face the same way when they are worn. Shown as a render of the printable model, not a photograph.

Design by Slowpoke’s Workshop

A mirrored flourish - a curling stem with leaf-shaped tips - cut 2 mm thick, each about 24 x 36 mm with a hole at the end of the stem for a hook. The pair prints flat as one piece and lies along the ear rather than hanging off it. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A flip-flop outline, 48 x 18 mm and 2 mm thick, with the strap drawn as an open line across the sole and an eyelet at the toe for a hook. Long and narrow, so the pair swings rather than sitting flat against the ear. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A plectrum printed flat at half a millimetre, 27 mm tall and 24 mm across, with the designer's design across the face - the pun in the name is the whole idea. Thin picks bend more than thick ones, so this is the one for strumming rather than for shredding. Designed by marshal.meacham and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by marshal.meacham

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

A flat-pack stand for holding earrings: a base plate, two uprights and a crossbar that slot into each other, with the uprights stepped so pairs hang at different heights instead of bunching. Assembled it is about 170 x 100 mm and stands 13 mm deep, big enough for a shelf or a dresser top. It prints as four flat pieces with no supports and comes to about 83 g of plastic. Shown as a render of the printable model, not a photograph.

Design by Recflying

A hot air balloon with its gores moulded in, the netting raised and a basket hanging under it on two lines, printed 1.9 mm thick. Each is 30 x 50 mm with a hole at the top of the envelope for a hook, and the pair prints together. Shown as a render of the printable model, not a photograph.

Design by ProtoEngineering

One continuous line draws a face in profile, cut out flat as an earring: 26 mm tall, 2 mm thick, with a hole at the top for a hook. Sold as a pair, mirrored so the two faces look at each other. Shown as a render of the printable model, not a photograph.

Design by Margen3d

A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by dhs

Four Halloween cutters - pumpkin, ghost, bat and the like - about 3" across each, printed with a cutting rim deep enough for biscuit dough or Play-Doh. One plate prints the set. Shown as a render, not a photo.

Design by Creaitivity Studio

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A lotus flower built from three rings of petals, the outer ones splayed and the inner ones cupped, so the flower has depth from every angle. Each is 42 x 41 mm and 2 mm thick with a hole worked into the top petal for a hook, and the pair prints side by side on one plate. Shown as a render of the printable model, not a photograph.

Design by Pistachio

A filigree arch: a curved band of scrollwork with the spaces cut right through, so it reads as lace from the front and sits like a crescent against the ear. Each is 26 x 34 mm and 2.3 mm thick with the hook tab at the top, and the pair is mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

Six hearts on one plate: a large pair at 31 x 28 mm and two smaller pairs at 12 x 11 mm and 10 x 9 mm, each with a smiling face and a hole for a hook. Sold as a set of three pairs - the large hearts for everyday, the two small pairs for a second piercing or to give away. Shown as a render of the printable model, not a photograph.

Design by Merche

A capo in two printed parts: a jaw that sits across the strings and the lever that clamps it down, 92 mm wide so it spans a standard six-string fretboard. It goes on the neck above the fret and holds the strings at the new position, which is what lets one shape be played in any key. Designed by Kevdev, a remix of the Guitar Capo by HarleyPrints, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Kevdev

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

A pair of sunglasses with the arms and a bridge moulded in, printed 2.5 mm thick and 32 mm across, with a hole in each arm for a hook. They are a joke that prints properly: the lenses are open, so the shape holds at this size and reads at a glance. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A dolphin inside an oval ring, 42 x 37 mm and 2.6 mm thick, with a small eyelet at the top for a hook. The dolphin is cut clear of the ring behind it, so the two shapes read separately and the pair hangs as two clean outlines. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Ghost1975w

A largemouth bass on a rock, mouth open, fins up, printed as one piece with the base built in: a shelf or desk piece for somebody who would rather be on the water. Two sizes, and both are measured off the designer's own files - 97 mm nose to tail, and 190 mm for the mantelpiece. The smaller one is the same mesh scaled down and supported, so the detail is the same at both sizes. Designed by AUTROJAN and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by AUTROJAN

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A six-fold filigree snowflake, 35 x 31 mm and 1.5 mm thick, with a hole at the top for a hook. Every branch is openwork, so it prints as fine line after fine line rather than a solid plate, and it catches the light as it moves. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by PediMR

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

XO in solid letters, 40 x 37 mm and 2 mm thick, with a small hole at the base of the O for a hook. The two letters are cut as one piece, so each earring hangs as a single word rather than two separate charms. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by SynneLuna

A cowboy boot with the shaft, pull tabs, heel and stitched sole all standing proud of the outline, so it reads as a boot rather than a silhouette. Each is 31 mm square and 2 mm thick with a hole in the shaft for a hook, and the pair prints mirrored. Shown as a render of the printable model, not a photograph.

Design by D.MacMcAlister

A heart drawn in a few asymmetric arcs, 34 x 29 mm and 2.3 mm thick, with a hole at the top for a hook. The plate is a solid rim around a cut-out centre, so it reads as a sketch of a heart rather than a filled one, and the pair hangs light. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A heart outline with a horse's head drawn inside it in one open cut, 40 x 37 mm and 2 mm thick, with a hole at the top of the heart for a hook. Almost all of it is outline, so it is light on the ear and reads as a horse from across a room rather than only up close. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

Two five-pointed stars, 35 mm across and 2 mm thick, a hole at the tip of one point for a hook. Printed flat in PLA with no supports, and light enough that the pair is about a gram and a half of plastic. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

A tulip built from flat overlapping layers - a rounded bloom sitting over its leaves - as a pair of earrings 21 mm tall and 2.4 mm thick, with a hole through the back for a hook. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by Ettore

A jeweller's display in one print: a smooth-shouldered bust form for necklaces, a hand for rings and bracelets, both on one base, plus the collar that finishes the neck. 244 mm tall and 233 mm wide - a shop-window piece rather than a bedside one - printed in the parts its designer drew, with a support blocker in the file so the overhangs print without a forest of supports. Designed by Murphy345 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Murphy345

A hinged box for rings and earrings, 150 by 83 by 20 mm closed: a tray with compartments, a lid that shuts on printed hinges, and two pins that press in to hold the hinge line - four printed parts, no screws, no supports. Small enough for a wash bag and rigid enough to keep its shape. A remix of "Parametric hinged small parts box" by Billiam on Printables, which is CC BY 4.0, and designed by Ivan Chamberlain under Creative Commons Attribution 4.0 (CC BY 4.0) - both are credited. Shown as a render of the printable model, not a photograph.

Design by Ivan Chamberlain

The classic folded awareness ribbon with a keyring loop at the top, printed flat so the fold reads cleanly on both faces. It is 2.5" long by 1.4" wide and prints in whatever colour you choose. Shown as a render, not a photo.

Design by Miss3DP

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

A paw that rides on top of a straw: the straw passes through the middle of it, the paw sits above the lid, and the raised pad and four toes catch the light as the cup moves. It is made for the 10 mm Stanley straws, 3.5" tall by 1.6" across, and it prints in one piece. Shown as a render, not a photo.

Design by Morganja

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.

Design by Morganja

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox