3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A rail that a CD jewel case stands in, ribbed along its length so the case leans back instead of sliding forward, on four short feet that keep the disc off the shelf. 149 mm wide and 30 mm tall - the width of a standard case, with a little room either side. Designed by ToToKia and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by ToToKia

A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by gareth7562

A practice mute for trombone, printed in three parts: the long tapered body that goes down into the bell, the flared cup that caps it, and the small collar that keeps the two together. 250 mm long and 193 mm across the cup, so it takes a full-size bell. The cup is what does the muting, so the horn can be played in an apartment without the neighbours learning the set list. Designed by 烤肉大师 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by 烤肉大师

Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by SF3DPrints

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A pen holder clad in raised dragon scales, hexagonal all the way round, with a smooth inner cup for pens, pencils or brushes. 3.1" across and 4" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3DWoosh

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A top that keeps going: a heavy rim, a fine point and a printed handle to spin it between finger and thumb. 2.1" across, about 41 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by happybirthday

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A clicker keychain with four buttons that press and click, printed in place so nothing needs assembling. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A ghost bookmark: a flat spectre that hooks over the page, thin enough not to splay the spine. There are seven of them in the file, each a slightly different ghost, so pick the one you want - about 1.2" by 4" and printed flat. Shown as a render, not a photo.

Design by PrintcessJacqueline3DDesigns

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A star that spins: the points are cut so it turns on its axis in the hand and keeps turning. Shown as a render, not a photo.

Design by CreaitivityStudio

A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.

Design by user_3738174853

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.

Design by ArmadilloFDM

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.

Design by TinkerTogether

A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.

Design by MakerShed

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D