3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

A planetary gear set printed in place: six small gears mesh between a sun gear and a toothed ring, so turning any one of them turns all the rest. It is 2.5" across and prints as a single piece with nothing to snap together. Shown as a render, not a photo.

Design by HurtTree

A desk caddy printed in one piece: a raised back that stands a phone at a reading angle, a round well for pens, and a square tray for a watch, keys or a card, with a slot for a charging cable to pass through. It is 7.1" wide by 3.5" deep. Shown as a render, not a photo.

Design by Maker76

A fidget spinner small enough to live in a pocket: one piece, no bearings, no axle to glue, printed in place so the two halves and their weights come off the plate ready to spin. It is a 15-minute print in the designer's own profile, which is why it makes a good giveaway or market-stock item. Printed in a silk filament the spinning face catches the light. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DragonFusion3D

A paw that rides on top of a straw: the straw passes through the middle of it, the paw sits above the lid, and the raised pad and four toes catch the light as the cup moves. It is made for the 10 mm Stanley straws, 3.5" tall by 1.6" across, and it prints in one piece. Shown as a render, not a photo.

Design by Morganja

A chunky little turtle with a big head, four stubby legs and a tiny tail, and a keyring loop moulded into its shell, so it sits on a desk or dangles off a bag. It is 1.6" by 1.2" and prints in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Type1Printing

A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.

Design by Morganja

A hexagonal tube cut into one continuous spiral, so it springs and flexes in the hand and the turns of the helix roll past each other under a thumb. It prints as a single piece and needs no assembly, and it stands 2.8" tall by 1.3" across. Shown as a render, not a photo.

Design by NerdHerder

A segmented caterpillar that wriggles: every segment is jointed to the next, printed as one piece with nothing to assemble and no supports, so it comes off the plate already moving. Two lengths - the short one at 5.4 inches and the longer twelve-segment version at 7.2 - and the longer one is the one to buy if you want it to drape and coil in your hand. Prints at 0.2 mm layers in PLA, and it takes a colour change well if you want the segments striped. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Timmy_1293

A shark in articulated segments, 110 mm from nose to tail, printed in one piece with the joints already free - it swims through the fingers and lies flat in a pocket. Printed exactly as its designer published it, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by goatbuster. Shown as a render of the printable model, not a photograph.

Design by goatbuster

A headband in a soft wave, 157 mm across and printed in PETG the way its designer publishes it - PETG bends where PLA would snap, and a headband is a part that gets flexed every time it is worn. Designed by Elyse_ and released as Creative Commons Public Domain (CC0 1.0), so the prints may be sold with no condition attached. Shown as a render of the printable model, not a photograph.

Design by Elyse_

A baby stone dragon in one piece: the plates of its body are jointed all the way down, so it curls and straightens and holds whatever shape you leave it in, and it stands on its four legs because the legs are part of the same print. This is the wingless one, so nothing catches on a sleeve or a shelf. Two sizes - 4.2 inches and a 2.5 inch pocket-sized version - both printed in place with no supports. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Bash Studio 3D

A headband with a horn and two ears, 205 mm across and 6 mm thick, so it sits flat on the head and prints in one piece on the plate with nothing to glue. The band is a loop rather than a rigid arc, so it grips a child's head and an adult's. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

An articulated baby dragon: the body, tail and neck are cut into segments joined by print-in-place hinges, with the head and its small horns on top. It is 4.5" long and prints in one piece. Choose the finish: solid is the plastic alone, and each extra colour is a filament change at the printer, charged at the shop's $1 a colour. Shown as a render, not a photo.

Design by BashStudio3D

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A crocodile printed as a chain of flexing segments, grin and all, with a ridged back and a tail that whips about. Three sizes - 4.7", 5.6" and 7.5" long - each printed in one piece. Shown as a render, not a photo.

Design by SHF3D

A phone stand that folds out of a keychain: the plate swings up and the phone leans back on it, and folded away it hangs on your keys. Shown as a render, not a photo.

Design by musielovsky

A braid tool: hook the strands through the slot and the plait forms as you pull, so a French braid takes half the time and no third hand. 5.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by Cy-Bea

A caterpillar printed as a chain of flexing segments with a face at one end, so it wriggles along your hand and curls up when you put it down. 6.7" long, printed in one piece, with no supports and no assembly. Shown as a render, not a photo.

Design by Pistachio

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose

A screw toy for small hands: three chunky bolts with matching nuts, the caps they screw into and a long threaded rod - the plate is the whole set. The rod is 7.1" long, and every part is printed oversized so a toddler can get a grip on it. Shown as a render, not a photo.

Design by hyperZ

A bunny printed as a chain of flexing segments with a carrot to go with it, so it curls up in your hand and springs straight again. The set prints as one plate - a 2.4" bunny and its carrot - and comes in a single colour or with the parts in different ones. Shown as a render, not a photo.

Design by TinkerTogether

A lizard printed in one piece with no AMS and no supports - ridged back, splayed feet and a tail that curls, sitting flat wherever you put it. Three sizes: 1.7", 3.7" and 4.6" long, the smallest small enough for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AmandaRoos

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A penguin that comes apart into a stack of rings and goes back together again - the plate carries the body, four rings and the little caps, so it builds up and knocks down like a nesting toy. About 3.6" across the widest ring. Shown as a render, not a photo.

Design by katinkus

A water dragon printed as a chain of flexing segments - ridges along the back, a finned tail, and no supports anywhere. 4.5" long, printed in one piece, and it settles into whatever shape you leave it in. Shown as a render, not a photo.

Design by TinkerTogether

Twelve little pals off one plate, each about two inches across and printed as a single piece, with no supports and nothing to assemble. Pick the one you want - the size on each chip is that pal's own width by height, so a 2.8"x1.6" one is a different creature from a 2.0"x1.4". Shown as a render, not a photo.

Design by Apricity

A little octopus printed as a chain of flexing segments, so its eight arms trail and curl behind it. 2.2" across, printed in one piece in a single colour or with the body and the arms in different ones. Shown as a render, not a photo.

Design by slavko

A baby spike dragon with a ridged back and a curled tail, small enough to sit on a desk or ride on a keyring. 1.9" long, printed in one piece at high detail. Shown as a render, not a photo.

Design by BashStudio3D

A smiley you can click: the face is the button, and it presses in and springs back with a sound. 3.2" across, printed in one piece with no AMS and no supports. Shown as a render, not a photo.

Design by AmandaRoos

Three holders that keep bottles lying down in the fridge instead of rolling out of the door - each cradles one bottle on its side and stacks with the others. The plate prints three, and each is about 9.4" long. Shown as a render, not a photo.

Design by RossMacAllan

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs

A little alligator printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles across the desk and settles into whatever shape you leave it in. 2.4" long, printed in one piece. Shown as a render, not a photo.

Design by Litolunar

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain

A jack-o-lantern that drowns fruit flies: bait goes in the cup, the lid funnels them down and they cannot get back out. 2.7" across, printed in two pieces with no supports - and it earns its place on the counter for a fortnight in October. Shown as a render, not a photo.

Design by PolaQ

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

Six coasters shaped like leaves, 70 mm across and 3 mm thick, each with a different vein pattern. Printed flat with no supports, and thin enough to stack in a drawer. Shown as a render, not a photo.

Design by jdormer9

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

Three stick figures in fighting poses, each one holding your pencil where it would hold a weapon: an archer drawing a pencil like a bow, a spearman resting on a long one, and a sniper kneeling with one as a rifle. The archer takes short pencils of about 8 to 9 cm, the other two take ordinary 10 to 16 cm ones. Sold as the set of three. Designed by Gekko and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Gekko

A Santa in his sleigh for the corner of a door frame: the sleigh runs behind him as a counterweight, so the piece sits up on its own along the top corner of a door or a window. The designer's updated file carries both the left-hand and the right-hand version, so the pair is what is printed. Designed by lindnjoe and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

An ornament that hooks over the corner of a door frame: a bauble hanging from a bow on the trim above a door, flat on the back so it sits square in the corner. Sold as one corner piece, 196 by 207 mm. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A little town under snow that prints as one piece: rooftops, houses and trees drifting into each other, with holes modelled through the houses so a micro LED string can be threaded in and the windows light from inside. This is the designer's fixed-roof version, and davidkelly021 publishes a separate base for it with room for a battery pack. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by davidkelly021

The words Merry Christmas in a flowing script, arranged in the shape of a Christmas tree: a star at the top and the swashes of the letters curling out into the branches. The line work is all joined into one flat piece, so it prints as a single item and hangs flat on a wall or a door. Designed by OrangeSs and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by OrangeSs